A ball bearing has been selected with the bore size specified in the catalog as 35.000 mm

Question:

A ball bearing has been selected with the bore size specified in the catalog as 35.000 mm to 35.020 mm. Specify appropriate minimum and maximum shaft diameters to provide a locational interference fit.

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Shigleys Mechanical Engineering Design

ISBN: 978-1121345317

9th edition

Authors: Richard G. Budynas, J. Keith Nisbett

See More Books

Question Posted: May 30, 2013 07:36 AM

See More Questions

A full journal bearing has a shaft journal diameter of 25 mm with a unilateral tolerance of 0.01 mm. The bushing bore has a diameter of 25.04 mm with a unilateral tolerance of 0.03 mm. The l/d ratio...
A journal bearing has a shaft diameter of 75.00 mm with a unilateral tolerance of 0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm...
A stepped shaft with diameters D1 = 40 mm and D2 = 60 mm is loaded by torques T = 1100 N ( m (see figure). If the allowable shear stress at the stress concentration is 120 MPa, what is the smallest...
One item is omitted in each of the following summaries of balance sheet and income statement data for the following four different corporations: Determine the missing amounts, identifying them...
Given that v(0) = 2 and dv(0)/ dt = 4 , solve 10e ul) dt dt
What are the basic problems that occur in the valuation of accounts receivable?
Assume the following exceptions to prescribed control procedures over cash receipts transactions occurred in the Janz Company: 1. A mail remittance was misappropriated after receipt. 2. A cash sale...
The following supplementary records summarize Tosca Companys merchandising activities for year 2013. Set up T- accounts for Merchandise Inventory and Cost of Goods Sold. Then record the summarized...
Regular Company produces audio equipment, specifically headphones and speakers. A new CEO has just been hired and announces a new policy that if a product cannot earn a markup of at least 25 percent,...
A four-cylinder, four-stroke diesel engine is used to generate an output of 200A at 210V. The generator and mechanical efficiencies are 90 % and 87%, respectively. The quantity of fuel supplied to...
A journal bearing and bushing need to be described. The nominal size is 1.25 in. What dimensions are needed for a 1.25-in basic size with a close running fit if this is a lightly loaded journal and...
A shaft diameter is carefully measured to be 1.5020 in. A bearing is selected with a catalog specification of the bore diameter range from 1.500 in to 1.501 in. Determine if this is an acceptable...
Use of boundary-layer equations, air at 1 atm and 20 o C flows tangentially on both sides of a thin, smooth flat plate of width W = 10 ft, and of length L = 3 ft in the direction of the flow. The...
A resort uses a rope to pull a $65-\mathrm{kg}$ skier up a slope at constant speed. To pull the skier $75 \mathrm{~m}$ requires $18 \mathrm{~kJ}$ of work to be done by the rope. (a) Determine...
A cylindrical solenoid of radius $R$ and height $b$ consists of $N$ windings. There is a current through the windings, and this current increases with time as $I=\alpha t$, where $\alpha$...
Suppose that $r=0, n=15$, and $s_{y}=10$. Determine $s$.
Identity theft is a growing problem in the United States. According to a Federal Trade Commission Report about 280,000 identity complaints were filed for 2011. Among the 43.2 million persons in the...
Prove that the matrices $\mathbf{H}$ and $\mathbf{I}-\mathbf{H}$ are idempotent, that is, $\mathbf{H H}=\mathbf{H}$ and $(\mathbf{I}-\mathbf{H})(\mathbf{I}-\mathbf{H})=\mathbf{I}-\mathbf{H}$.
Write a method mazeGenerator that takes as an argument a two-dimensional 12-by-12 character array and randomly produces a maze. The method should also provide the starting and ending locations of the...
What is a lobbyist in US? How did this term emerge?
Comment on the conditions appropriate to (a) unstructured decisions and (b) structured decisions.
Describe applications of machine vision for specific parts, similar to the examples shown in Fig. 14.26?
14.39Add examples of guides other than those shown in Fig. 14.31?
Explain the difference between hard and soft automation. Why are they named as such?
Two blocks are stacked on top of one another (7 kg and 12 kg). A 50 N force is applied to the bottom block. There is 8 N of friction between the bottom block and the desk. Show a free body diagram...
2) A load of bricks with mass m = 15.0 kg hangs from one end of a rope that passes over a massless, frictionless pulley. A counterweight of mass m2 = 28.0 kg is suspended from the other end of the...
The figure below shows forces acting at various points on a metal shaft. The angles a = 40, = 29, y = 17. The length = 4.4 m. Find the net torque (in N m) on the shaft about the following axes. 25 N...

A ball bearing has been selected with the bore size specified in the catalog as 35.000 mm

Question:

Step by Step Answer:

Choose basic size D d 35 mm From Table 79 a locational interference fit is designated as H7p6 From ...View the full answer

Shigleys Mechanical Engineering Design

Students also viewed these Mechanical Engineering questions