An AISI 1040 cold-drawn steel tube has an OD = 50 mm and wall thickness 6 mm.
Question:
An AISI 1040 cold-drawn steel tube has an OD = 50 mm and wall thickness 6 mm. What maximum external pressure can this tube withstand if the largest principal normal stress is not to exceed 80 percent of the minimum yield strength of the material?
Fantastic news! We've Found the answer you've been seeking!
Step by Step Answer:
Answer rating: 76% (13 reviews)
From Table A20 Sy490 MPa F...View the full answer
Answered By
Utsab mitra
I have the expertise to deliver these subjects to college and higher-level students. The services would involve only solving assignments, homework help, and others.
I have experience in delivering these subjects for the last 6 years on a freelancing basis in different companies around the globe. I am CMA certified and CGMA UK. I have professional experience of 18 years in the industry involved in the manufacturing company and IT implementation experience of over 12 years.
I have delivered this help to students effortlessly, which is essential to give the students a good grade in their studies.
3.50+
2+ Reviews
10+ Question Solved
Related Book For
Shigleys Mechanical Engineering Design
ISBN: 978-1121345317
9th edition
Authors: Richard G. Budynas, J. Keith Nisbett
Question Posted:
Students also viewed these Mechanical Engineering questions
-
An AISI 1020 cold-drawn steel tube has an ID of 40 mm and an OD of 50 mm. What maximum internal pressure can this tube take if the largest principal normal stress is not to exceed 80 percent of the...
-
An AISI 1020 cold-drawn steel tube has an ID of 1 in and an OD of 1 in. What maximum external pressure can this tube take if the largest principal normal stress is not to exceed 80 percent of the...
-
The cold-drawn AISI 1040 steel bar shown in the figure is subjected to a completely reversed axial load fluctuating between 28 kN in compression to 28 kN in tension. Estimate the fatigue factor of...
-
Why do we need to calculate beginning Retained Earnings and beginning NCI when preparing consolidated financial statements using the worksheet method.
-
Determine the hybrid parameters for the network in Fig. 19.89. 2 41 O-
-
1. Do you agree with Alice and the others about the importance of problem-solving skills? Industry-specific insight? Communication skills? Discuss. 2. Should you research how a hospital is managed...
-
An airplane weighs \(320,000 \mathrm{lb}\), has a wing area of \(2800 \mathrm{ft}^{2}\), and has a wing length of \(140 \mathrm{ft}\). The atmospheric pressure and temperature are \(14.67...
-
Use the indirect method to determine cash flows from operating activities Hong Company presents its statement of cash flows using the indirect method. The following accounts and corresponding...
-
A model of a helicopter rotor has four blades, each is 3.40 m long from the central shaft to the blade tip. The rotor takes 0.02 s to spin one revolution. Find the linear speed of the blade tip. What...
-
Consider the Sherwin-Williams Company example discussed in this chapter (see Table 4.1). Suppose one is interested in developing a simple regression model with paint sales (Y) as the dependent...
-
A pressure cylinder has an outer diameter do, wall thickness t, external pressure po, and maximum allowable shear stress Ïmax. In the table given, determine the appropriate value ofx. Tmax do...
-
Repeat Prob. 3100 with an OD of 2 in and wall thickness of 0.25 in. Repeat Prob. 3100, An AISI 1040 cold-drawn steel tube has an OD = 50 mm and wall thickness 6 mm. What maximum external pressure can...
-
Transformer 1 has a primary voltage Vp and a secondary voltage Vs. Transformer 2 has twice the number of turns on both its primary and secondary coils compared with transformer 1. If the primary...
-
Un Company sold office equipment with a cost of $42,750 and accumulated depreciation of $40,077 for $5,030. Required a. What is the book value of the asset at the time of sale? b. What is the amount...
-
Greenwood Company manufactures two products-14,000 units of Product Y and 6,000 units of Product Z. The company uses a plantwide overhead rate based on direct labor-hours. It is considering...
-
Answer these two questions on the Consumer Behavior Subculture of Hispanics in paragraphs (150 words) in each question. (Please answer each question correctly, and ill thumbs up!!) 1. What is the...
-
A purchase of machine tools by Jet Co. for $2,450 should have been capitalized as the tools have a 3 year life and an expected residual value of $350. However, Jet Co. erroneously charged the...
-
Sheffield Corporation began its latest fiscal year on January 1, 2023, with 470,000 common shares outstanding. During the year, the following events occurred: On February 1, Sheffield sold 16,200...
-
Specify the sets in Problems 1520 by description. {1, 2, 3, 4, 5, 6, 7, 8, 9}
-
Using a graphing utility, graph y = cot -1 x.
-
Direct labor costs incurred by a federal agency during a period will be reflected in the agency's budgetary accounts as a. a debit to Expended Appropriations and credit to Cash. b. a debit to...
-
To determine its forgeability, a hot-twist test performed on a round bar 25 mm in diameter and 200 mm long. It is found that the bar underwent 200 before it fractured. Calculate the shear strain at...
-
What is the magnitude of when, for plane-compression, the forging load with sliding fric-is equal to the load with sticking friction? Use average-pressure formulas.
-
Explain why there might be a change in the density of a forged product as compared to that of the cast blank.
-
Identify an area of Financial Services where you feel significant opportunities lie in relation to process management. Why do you feel this?
-
1. Given the functions f(x) = x + 1 and g(x) = 3-x, determine an equation for the combined function y = f(x)+ g(x). 2. If f= {(-7, 1), (-5, 8), (3, 11), (5,-1)) and g = {(-6, 4), (-5, 3), (-1, 7),...
-
What is urban economics and what components of a city usually results in higher demand of a city's real estate. Describe at least three
Study smarter with the SolutionInn App