Consider the diffusion of oxygen through a low-density polyethylene (LDPE) sheet 15 mm thick. The pressures of
Question:
Consider the diffusion of oxygen through a low-density polyethylene (LDPE) sheet 15 mm thick. The pressures of oxygen at the two faces are 2000 kPa and 150 kPa, which are maintained constant. Assuming conditions of steady state, what is the diffusion flux [in [(cm3STP)/cm2-s] at 298 K?
Fantastic news! We've Found the answer you've been seeking!
Step by Step Answer:
Answer rating: 42% (7 reviews)
This is a permeability problem in which we are asked to compute the diffusion flux of oxygen ...View the full answer
Answered By
Moses mwangi
With prior writing experience, be sure that I will give a great grade, If not an A+, it will be something close to this. My reviews speaks it all, Try me!!
4.80+
78+ Reviews
157+ Question Solved
Related Book For
Materials Science and Engineering An Introduction
ISBN: 978-1118324578
9th edition
Authors: William D. Callister Jr., David G. Rethwisch
Question Posted:
Students also viewed these Modern Physics questions
-
Consider the diffusion of water vapor through a polypropylene (PP) sheet 2 mm thick. The pressures of H2O at the two faces are 1 kPa and 10 kPa, which are maintained constant. Assuming conditions of...
-
The permeability coefficient of a type of small gas molecule in a polymer is dependent on absolute temperature according to the following equation: where and Qp are constants for a given gas-polymer...
-
Consider the diffusion of water vapor through a polypropylene (PP) sheet 2 mm thick. The pressures of H2O at the two faces are 1 kPa and 10 kPa, which are maintained constant. Assuming conditions of...
-
The inequality describes the range of monthly average temperatures T in degrees Fahrenheit at a certain location. (a) Solve the inequality. (b) If the high and low monthly average temperatures...
-
The CIO radical decays rapidly by way of the reaction, 2 CIO ---7Cl, + Oz. The following data have been obtained: Determine the rate constant of the reaction and the half-life of a CIO radical. t/(10...
-
The process by which we determine limits of rational functions applies equally well to ratios containing noninteger or negative powers of x: Divide numerator and denominator by the highest power of x...
-
PML Manufacturing, Inc., a privately held corporation, manufactures office equipment. The cash receipts portion of the revenue cycle is described below: 1. Mail is opened in the mailroom. Remittances...
-
Stevenson Apparel is a manufacturer of fashion clothing that has just opened its first large retail store for selling in-season clothes at regular prices. The companys competitive strategy depends on...
-
12. The amount of kinetic energy an object has depends on what? 13. What is the acceleration of a train that starts from rest and reaches the speed of 105m/s in 30.0 seconds? 14. The speed of a car...
-
The velocity graph of a braking car is shown. Use it to estimate the distance traveled by the car while the brakes are applied. (ft/s) 60 40 20 (seconds)
-
The density and associated percent crystallinity for two polypropylene materials are as follows: (g/cm3) ..................... crystallinity (%) 0.904 ....................................... 62.8...
-
Carbon dioxide diffuses through a high-density polyethylene (HDPE) sheet 50 mm thick at a rate of 2.2 10-8(cm3STP)/cm2-s at 325 K. The pressures of carbon dioxide at the two faces are 4000 kPa and...
-
Find the equation of the tangent to the circle x 2 + y 2 4x 1 = 0 at the point (1, 2).
-
What are the Important parameters of Economic growth of the country?
-
Michael s company uses a single predetermined overhead rate using direct labor hours as the allocation base ( driver ) . a ) Calculate the Predetermined Overhead Rate given the following information:...
-
Toma company uses process costing. Materail are added at the beginning of the process while conversion costs are added evenly though time. Units of WIP at December 31 were 32,000 and 70% completed...
-
In two or three sentences, evaluate the profitability and liquidity of the company below, given the information provided. You must include at least two ratio calculations to justify your answer....
-
Calculate the predetermined over head rate assuring sandhill company estimates total manufacturing overhead costs of 1 0 0 8 0 0 0.
-
Suppose the spot and three-month forward rates for the yen are 79.12 and 78.64, respectively. a. Is the yen expected to get stronger or weaker? b. What would you estimate is the difference between...
-
Global.asax is used for: a. declare application variables O b. all other answers are wrong O c. declare global variables O d. handle application events
-
A cylindrical piece of steel 75 mm (3 in.) in diameter is to be austenitized and quenched such that a minimum hardness of 40 HRC is to be produced throughout the entire piece. Of the alloys 8660,...
-
A cylindrical piece of steel 38 mm (1 1/2in.) in diameter is to be austenitized and quenched such that a microstructure consisting of at least 80% martensite will be produced throughout the entire...
-
A cylindrical piece of steel 90 mm (3 1/2 in.) in diameter is to be quenched in moderately agitated water. Surface and center hardnesses must be at least 55 and 40 HRC, respectively. Which of the...
-
(a) Argue that sin(x)dx = f sin(x)dx + fo sin(x)dx, and use this to compute a (b) Explain how to calculate where u, v, f are functions. (c) Let a >0. Calculate d da L sin(x)dx -a d v(a) f(x)dx da d...
-
= [(-1)* (2m)!" 12. Using Maclaurin series of cosx=(-1)*- A. Find Maclaurin series of cosx. B. Using the 1st four terms of Maclaurin series of cosx to evaluate focos x dx (leave answer to four...
-
Confirm that the below limit meets the conditions to apply l'Hpital's Rule and then solve the limit. Be sure to address these conditions in your explanation. Enter an exact numeric answer. lim In(x)...
Study smarter with the SolutionInn App