Estimate the relative cost of grinding a steel part to a tolerance of 0.0005 in versus
Question:
Estimate the relative cost of grinding a steel part to a tolerance of ± 0.0005 in versus turning it to a tolerance of ± 0.003 in.
Fantastic news! We've Found the answer you've been seeking!
Step by Step Answer:
Answer rating: 84% (13 reviews)
From Fig 12 cost of grinding to 00005 in is 270 Cost of t...View the full answer
Answered By
Branice Buyengo Ajevi
I have been teaching for the last 5 years which has strengthened my interaction with students of different level.
4.30+
1+ Reviews
10+ Question Solved
Related Book For
Shigleys Mechanical Engineering Design
ISBN: 978-1121345317
9th edition
Authors: Richard G. Budynas, J. Keith Nisbett
Question Posted:
Students also viewed these Mechanical Engineering questions
-
In traverse surface grinding of a steel workpiece, 3 inch by 6 inch by 9 inch large, as shown in the following figure, the 90 grit aluminum oxide grinding wheel has a diameter (D) of 6 inches. The...
-
It was stated in Section 9.5.2 that, in practice, grinding ratios typically range from 2 to 200. Based on the information given in Section 9.13, estimate the range of wear ratios in...
-
Estimate the percent increase in the cost of the grinding operation if the specification for the surface finish of a part is changed from 63 in. to 16 /in?
-
A very long insulating cylinder of charge of radius 2.40 cm carries a uniform linear density of 13.0 nC/m. If you put one probe of a voltmeter at the surface, how far from the surface must the other...
-
Consider the one-dimensional data set shown in Table 5.4. (a) Classify the data point x = 5.0 according to its 1-, 3-, 5-, and 9-nearest neighbors (using majority vote). (b) Repeat the previous...
-
Hasbro used to manufacture a toy called Wonder World Aquarium. The toy included a powder that, when mixed with water, formed a gel that filled a plastic aquarium. Children could then place plastic...
-
For oil \(\left(S G=0.86, \mu=0.025 \mathrm{Ns} / \mathrm{m}^{2} ight.\) ) flow of \(0.2 \mathrm{~m}^{3} / \mathrm{s}\) through a round pipe with diameter of \(500 \mathrm{~mm}\), determine the...
-
1. What methods did Smart USA use to test market the Smart Fortwo car among prospective customers? 2. What trends are influencing the market potential of the Smart Fortwo car? 3. How does Smart USA...
-
Jamie Lee Jackson, age 27, full-time student and part-time bakery employee, has just moved into a bungalow-style, unfurnished home of her own. The house is only a one-bedroom, but the rent is...
-
Joan Taylor, the administrator of Life-Time Insurance Company, which is based in Buffalo, New York, was charged with establishing a health maintenance organization (HMO) satellite clinic in Austin,...
-
Selected financial statements from a recent annual report of The GAP Inc. follow. Use these statements to answer the following questions. Required: 1. What amounts did The GAP report for the...
-
The costs to manufacture a part using methods A and B are estimated by CA= 10 + 0.8 P and CB = 60 + 0.8 P 0.005 P2 respectively, where the cost C is in dollars and P is the number of parts. Estimate...
-
Calculate the standard entropy change for the following reactions at 25C. Comment on the sign of r S. (a) 2 Na(s) + 2 H 2 O() 2 NaOH(aq) + H 2 (g) (b) Na 2 CO 3 (s) + 2 HCl(aq) 2 NaCl(aq) + H 2...
-
Subtract: (17 7i) - (10+ 22i) difference =
-
Joyeux Trophees Inc. (JTI) manufactures and sells medals for sporting events. Its factory has a production capacity of 15,000 units per year. Currently, monthly production is 90% of capacity. All...
-
Create an audit strategy for a business of your preference to assess the internal control system implemented by management in the Revenue and Expense Cycles. Emphasize the utilization of data...
-
Q1. Darpan Electrical Works has a stock of about 5,000 units of a specific wire purchased at the rate of $2 each. The present value of each unit has risen to $5. The owner decides that he would use...
-
Lab 3: Kirchhoff's Voltage and Current Laws Objective The objective of this Lab activity is to verify Kirchhoff's Voltage Law (KVL) and Kirchhoff's Current Law (KCL) using mesh and nodal analysis of...
-
Find equations r = g(, z) (cylindrical) and = (, ) (spherical) for the hyperboloid x 2 + y 2 = z 2 + 1 (Figure 18). Do there exist points on the hyperboloid with = 0 or ? Which values of occur for...
-
Archangel Corporation prepared the following variance report. Instructions Fill in the appropriate amounts or letters for the question marks in the report. ARCHANGEL CORPORATION Variance...
-
Carter County, like all other counties in the state, shares in the proceeds of a state-levied sales tax. The state requires all recipient counties to use the proceeds for capital improvements to...
-
An AISI 1040 cold-drawn steel tube has an outside diameter of 50 mm and an inside diameter of 42 mm. The tube is 150 mm long, and is capped on both ends. An internal pressure of 40 MPa is applied....
-
An AISI 1040 cold-drawn steel tube has an outside diameter of 50 mm and an inside diameter of 42 mm. The tube is 150 mm long and is capped at both ends. Determine the maximum allowable internal...
-
The shaft AB in Problem 3-55 is made from AISI 1035 CD steel. Based on failure at the wall at A, determine the factor of safety using. Data in Problem 3-55 The part shown is loaded at point B with...
-
Within the context of rapidly evolving regulatory landscapes and heightened ethical scrutiny, how do advanced organizations navigate the ethical complexities of technological innovation and...
-
Write a program that accepts an integer limit and an integer value and that prints a complete line of output reporting the multiples of value uptil the limit . Keep prompting the user for a value...
-
BRAND SELF COLLATERAL What is your brand name? What is your logo (YOU MUST DESIGN IT What is your brand slogan (the phrase that defines your brand and yourself) What are celebrity spokesperson is...
Study smarter with the SolutionInn App