In reading this chapter, you will have noted that the specific term dimensional tolerance is often used,

Question:

In reading this chapter, you will have noted that the specific term dimensional tolerance is often used, rather than just the word tolerance. Do you think this distinction is important? Explain.

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Manufacturing Processes for Engineering Materials

ISBN: 978-0132272711

5th edition

Authors: Serope Kalpakjian, Steven Schmid

See More Books

Question Posted: Jul 18, 2016 08:55 AM

See More Questions

This chapter has assumed that lengths perpendicular to the direction of motion are not affected by the motion. That is, motion in the x-direction does not cause length contraction along the y- or...
Cosmological redshift the expansion of the universe is often represented with a drawing like Figure a. In that figure, we are located at the symbol labeled MW (for the Milky Way galaxy), at the...
Cosmological red shift. The expansion of the universe is often represented with a drawing like Fig. 44-15a. In that figure, we are located at the symbol labeled MW (for the Milky Way galaxy), at the...
Using the 526 observations on workers in a certain dataset, we include educ (years of education), exper (years of labor market experience) and tenure (years with the current employer) in regression...
Explain what effect a large federal deficit might have on interest rates.
Lower-of-Cost-or-Market Riegel Company uses the lower-of-cost-or-market method, on an individual-item basis, in pricing its inventory items. The inventory at December 31, 2011, consists of products...
A uniform fixed-fixed beam of length $2 l$ is simply supported at the middle point. Derive the frequency equation for the transverse vibration of the beam.
Mark Johnson saves a fixed percentage of his salary at the end of each year. This year he saved $1500. For the next 5 years, he expects his salary to increase at an 8% annual rate, and he plans to...
evaluated the operating performance of Dunn Company's six divisions. Veronica made the following presentation to Dunn's board of directors and suggested the Percy Division be eliminated. "If the...
Kai is the president of Zebra Antiques. An employee, Reese Francis, is due a raise. Reeses current benefit analysis is as follows: Compute the benefit analysis assuming: 3 percent increase in pay. ...
Identify factors that can cause a process to become out of control. Give several examples of such factors.
Give an example of an assignable variation and a chance variation.
A container can be made from steel [( = 36 10-6 (Co)-1] or lead [ = 87 10-6 (Co)-1]. A liquid is poured into the container, filling it to the brim. The liquid is either water [ = 207 10-6 (Co)-1]...
Water is supplied to a fountain via a large pipe. Somewhere along the flow path a troublesome teenager injects a soap solution at a rate of 3 . 2 4 g / s in an attempt to create a grand sudsy mess....
A certain low-loss non-magnetic dielectric material has a relative permittivity (er) of 2.5 and a loss tangent of 0.004. What is the phase constant b of a plane wave of frequency 11.3 GHz?
A trebuchet is a mighty siege engine capable of flinging 90-kg projectiles a distance of 300 meters. Assuming a perfect launch angle of 45, calculate the speed with which one of these projectiles...
An 76 kg man starts from rest and after 1.60 seconds is running at a speed of 11.0 m/s. The force needed for this man to get up to this speed in 1.60 seconds is ____ N.
A string has a mass of 6.80 g, is 84.0 cm long, and has a tension of 46.0 N. If you wish to generate a wave of frequency 440.0 Hz and amplitude 0.550 mm, how much power must you supply to the string?...
For the following exercises, find the length of side x. Round to the nearest tenth. 42 3.4 4.5 x
A bar of a steel alloy that exhibits the stress-strain behavior shown in Figure 6.22 is subjected to a tensile load; the specimen is 375 mm (14.8 in.) long and has a square cross section 5.5 mm (0.22...
A four-strand no. 40 roller chain transmits power from a 21-tooth driving sprocket to an 84-tooth driven sprocket. The angular speed of the driving sprocket is 2000 rev/min. (a) Estimate the chain...
A 700 rev/min 25-hp squirrel-cage induction motor is to drive a two-cylinder reciprocating pump, out-of-doors under a shed. A service factor Ks of 1.5 and a design factor of 1.1 are appropriate. The...
A centrifugal pump is driven by a 50-hp synchronous motor at a speed of 1800 rev/min. The pump is to operate at 900 rev/min. Despite the speed, the load is smooth (Ks = 1.2). For a design factor of...
Direct materials Fixed manufacturing overhead costs Sales price Variable manufacturing overhead Direct labor Fixed marketing and administrative costs Units produced and sold during the quarter...
Provide documentation of a step by step training plan for a beta fish. What will be the primary reinforcer? How will you cue the behavior? What schedule of reminforcement will you use. What is the...
On May 1, Soriano Company reported the following account balances along with their estimated fair values: Items Carrying Amount Fair Value Receivables Inventory Copyrights Patented technology Total...

In reading this chapter, you will have noted that the specific term dimensional tolerance is often used,

Question:

Step by Step Answer:

Dimensional tolerance defined as the sufficient variation in the dimensions s...View the full answer

Manufacturing Processes for Engineering Materials

Students also viewed these Mechanical Engineering questions