# Question: Refer to the information for Diviney Manufacturing on the previous

Refer to the information for Diviney Manufacturing on the previous page.

a. A manual insertion process takes 30 minutes and 8 pounds of material to produce a product. Automating the insertion process requires 15 minutes of machine time and 7.5 pounds of material. The cost per labor hour is $ 12, the cost per machine hour is $ 8, and the cost per pound of materials is $ 10.

b. With its original design, a gear requires 8 hours of setup time. By redesigning the gear so that the number of different groves needed is reduced by 50 percent, the setup time is reduced by 75 percent. The cost per setup hour is $ 50.

c. A product currently requires 6 moves. By redesigning the manufacturing layout, the number of moves can be reduced from 6 to 0. The cost per move is $ 20.

d. Inspection time for a plant is 16,000 hours per year. The cost of inspection consists of salaries of 8 inspectors, totaling $ 320,000. Inspection also uses supplies costing $ 5 per inspection hour. The company eliminated most defective components by eliminating low-quality suppliers. The number of production errors was reduced dramatically by installing a system of statistical process control. Further quality improvements were realized by redesigning the products, making them easier to manufacture. The net effect was to achieve a close to zero-defect state and eliminate the need for any inspection activity.

e. Each unit of a product requires 6 components. The average number of components is 6.5 due to component failure, requiring rework and extra components. Developing relations with the right suppliers and increasing the quality of the purchased component can reduce the average number of components to 6 components per unit. The cost per component is $ 500.

f. A plant produces 100 different electronic products. Each product requires an average of 8 components that are purchased externally. The components are different for each part. By redesigning the products, it is possible to produce the 100 products so that they all have 4 components in common. This will reduce the demand for purchasing, receiving, and paying bills. Estimated savings from the reduced demand are $ 900,000 per year.

Required:

Estimate the nonvalue-added cost for each situation.

a. A manual insertion process takes 30 minutes and 8 pounds of material to produce a product. Automating the insertion process requires 15 minutes of machine time and 7.5 pounds of material. The cost per labor hour is $ 12, the cost per machine hour is $ 8, and the cost per pound of materials is $ 10.

b. With its original design, a gear requires 8 hours of setup time. By redesigning the gear so that the number of different groves needed is reduced by 50 percent, the setup time is reduced by 75 percent. The cost per setup hour is $ 50.

c. A product currently requires 6 moves. By redesigning the manufacturing layout, the number of moves can be reduced from 6 to 0. The cost per move is $ 20.

d. Inspection time for a plant is 16,000 hours per year. The cost of inspection consists of salaries of 8 inspectors, totaling $ 320,000. Inspection also uses supplies costing $ 5 per inspection hour. The company eliminated most defective components by eliminating low-quality suppliers. The number of production errors was reduced dramatically by installing a system of statistical process control. Further quality improvements were realized by redesigning the products, making them easier to manufacture. The net effect was to achieve a close to zero-defect state and eliminate the need for any inspection activity.

e. Each unit of a product requires 6 components. The average number of components is 6.5 due to component failure, requiring rework and extra components. Developing relations with the right suppliers and increasing the quality of the purchased component can reduce the average number of components to 6 components per unit. The cost per component is $ 500.

f. A plant produces 100 different electronic products. Each product requires an average of 8 components that are purchased externally. The components are different for each part. By redesigning the products, it is possible to produce the 100 products so that they all have 4 components in common. This will reduce the demand for purchasing, receiving, and paying bills. Estimated savings from the reduced demand are $ 900,000 per year.

Required:

Estimate the nonvalue-added cost for each situation.

**View Solution:**## Answer to relevant Questions

Refer to the information for Diviney Manufacturing on the previous page. a. A manual insertion process takes 30 minutes and 8 pounds of material to produce a product. Automating the insertion process requires 15 minutes of ...Hammer Company produces a variety of electronic equipment. One of its plants produces two laser printers: the deluxe and the regular. At the beginning of the year, the following data were prepared for this plant: In ...Morrisom National Bank has requested an analysis of checking account profitability by customer type. Customers are categorized according to the size of their account: low balances, medium balances, and high balances. The ...Consider the following conversation between Leonard Bryner, president and manager of a firm engaged in job manufacturing, and Chuck Davis, certified management accountant, the firmâ€™s controller. Leonard: Chuck, as you ...Multiple-Choice Questions 1. A budget a. Is a long-term plan. b. Covers at least two years. c. Is only a control tool. d. Is a short-term financial plan. e. Is necessary only for large firms. 2. Which of the following ...Post your question