1 A gear train is to be designed to transmit power from shaft 1 to shaft...
Fantastic news! We've Found the answer you've been seeking!
Question:
Transcribed Image Text:
1 A gear train is to be designed to transmit power from shaft 1 to shaft 2 with the following conditions: (i) Shaft 1 (driven by an electric motor) rotates at 100 revs min-. (ii) Shaft 2 is to rotate at 400 revs min-1 in the opposite direction to shaft 1 against a load of 200 Nm. The centre of shaft 1 is 300 mm from shaft 2. The minimum number of teeth on any gear is 15. All gears must have a multiple of 5 teeth and have a module of 2 mm. (iii) (iv) (v) (vi) (vii) The maximum number of gears permissible is 4 gears and the diameter of the largest gear must be minimized. (b) (c) (d) The centres of the gears should lie on a line which is as close to straight as possible. All gear shafts have a frictional resistance of 5 Nm. Carry out the following: (a) Design a gear train which satisfies the above criteria. Use a sketch to illustrate your design, label the gears A, B, C, etc. from the driver to the driven gear and state the number of teeth on each gear. Determine the input power required at shaft 1. Specify the efficiency of the gear train as a percentage. Determine an equation for the efficiency of the gear train in terms of the load (torque) on shaft 2 with all other factors remaining constant. 1 A gear train is to be designed to transmit power from shaft 1 to shaft 2 with the following conditions: (i) Shaft 1 (driven by an electric motor) rotates at 100 revs min-. (ii) Shaft 2 is to rotate at 400 revs min-1 in the opposite direction to shaft 1 against a load of 200 Nm. The centre of shaft 1 is 300 mm from shaft 2. The minimum number of teeth on any gear is 15. All gears must have a multiple of 5 teeth and have a module of 2 mm. (iii) (iv) (v) (vi) (vii) The maximum number of gears permissible is 4 gears and the diameter of the largest gear must be minimized. (b) (c) (d) The centres of the gears should lie on a line which is as close to straight as possible. All gear shafts have a frictional resistance of 5 Nm. Carry out the following: (a) Design a gear train which satisfies the above criteria. Use a sketch to illustrate your design, label the gears A, B, C, etc. from the driver to the driven gear and state the number of teeth on each gear. Determine the input power required at shaft 1. Specify the efficiency of the gear train as a percentage. Determine an equation for the efficiency of the gear train in terms of the load (torque) on shaft 2 with all other factors remaining constant.
Expert Answer:
Answer rating: 100% (QA)
a To design a gear train that satisfies the given criteria we need to consider the rotational speeds torques distances and gear specifications Lets go step by step 1 Calculate the speed ratio The spee... View the full answer
Related Book For
Shigleys Mechanical Engineering Design
ISBN: 978-1121345317
9th edition
Authors: Richard G. Budynas, J. Keith Nisbett
Posted Date:
Students also viewed these mechanical engineering questions
-
ttth Suppose that the sequence of bags {Bn | n N} is recursively enumerated by the computable function e(n, x) = fn(x), [7 marks] Hence prove that the set of all recursive bags cannot be recursively...
-
Let i and j be positive integers. (i) Prove that there exist natural numbers a and b such that ai = bj+gcd(i, j). You may use standard results provided that you state them clearly. [4 marks] (ii) Let...
-
A chemical is spilled into a lake of pure water and the concentration of chemicals in this lake is 4 If 20 of the water in the lake is replaced with clean in one month then. What will be the...
-
On July 16, 20Y1, Wyatt Corp. purchased 40 acres of land for $350,000. The land has been held for a future plant site until the current date, December 31, 20Y9. On December 18, 20Y9, TexoPete Inc....
-
Bob Sample and other student investors opened Campus Laundromat Inc. on September 1, 2014. During the first month of operations, the following transactions occurred. The chart of accounts for the...
-
Derive the equation for thermal efficiency of Rankine cycle.
-
Pinewood Company purchased two buildings on four acres of land. The lump-sum purchase price was $900,000. According to independent appraisals, the fair values were $450,000 (building A) and $250,000...
-
(in thousands, except per share amounts) Assets Current assets: February 1, 2020 February 2 2019 Cash and cash equivalents 361,930 $ 333,330 Short-term investments (available for sale) 55,000 92,135...
-
Imagine that instead of pipetting up to 1 mL of the 50-ppm stock solution of nitrite, you pipetted between 10-50 mL of the stock solution to make your standard solutions. What would your calibration...
-
Discuss the difference between constitution and constitutionalism?
-
Neil Frasier, a friend of your family, is a very proficient accountant. Hes 61 and has spent his entire career working at the Sears Holdings Corp. headquarters in Chicago. He just got a call from a...
-
Do you think facilitating payments (speed payments) should be ethical? Does it matter in which country, or part of the world, such payments are made?
-
Trump was right that GM had made a major bet on China. GM has been operating in China since 1997 when it established a joint venture with SAIC Motor, a Chinese state-owned automotive design and...
-
Promoting respect for universal human rights is a central dimension of many countries foreign policy. As history has shown, human rights abuses are an important concern worldwide. Some countries are...
-
A manager from a developing country is overseeing a multinationals operations in a country where drug trafficking and lawlessness are rife. One day, a representative of a local big man approaches the...
-
3. Show that A x Ua =U{A x X|Xe 8).
-
Outline some of the major problems confronting an international advertiser.
-
Repeat Prob. 357 with an allowable shear stress of 20 kpsi and a power of 50 hp. Repeat Prob. 357, Using a maximum allowable shear stress of 70 MPa, find the shaft diameter needed to transmit 40 kW...
-
Brinell hardness tests were made on a random sample of 10 steel parts during processing. The results were HB values of 230, 232(2), 234, 235(3), 236(2), and 239. Estimate the mean and standard...
-
A parallel helical gearset consists of a 19-tooth pinion driving a 57-tooth gear. The pinion has a left-hand helix angle of 30, a normal pressure angle of 20, and a normal module of 2.5 mm. Find: (a)...
-
Select a publicly traded company or use a company assigned by your instructor. Using the firms most recent Form 10-K report (accessed through the SEC EDGAR database or from the companys website),...
-
Research Problem Access the FASB website: https://fasb.org. Locate information about updates to accounting standards in the most recent year listed. Choose one of the updates and write a short essay...
-
What reports are required to be filed regularly with the SEC?
Study smarter with the SolutionInn App