3. Consider the solidification of a 10-micron rod based on the alloy indicated for each student...
Fantastic news! We've Found the answer you've been seeking!
Question:
Transcribed Image Text:
3. Consider the solidification of a 10-micron rod based on the alloy indicated for each student in the table below. For the given alloy, draw the solid concentration curve that will occur in the equilibrium state and Scheil solidification curve along the length of the rod. (Draw the phase diagram for the indicated alloy using Thermo- Calc software and use the necessary values from this diagram.) Al-13(wt.%)cu Solid Liquid 4. Repeat the 3rd question using Thermo-Calc software and compare the results obtained with Thermo-Calc and those found in the 3rd question. Clearly specify the Thermo-Calc procedure and include relevant diagrams and screenshots. 5. Based on the composition changes in the solid and/or liquid, draw at least 3 different representative microstructures for the alloy provided to you, considering equilibrium and Scheil solidification results (i.e. at points such as solid+liquid at high temperature, solid+liquid at lower temperature, and at room temperature). Compare these microstructures. 3. Consider the solidification of a 10-micron rod based on the alloy indicated for each student in the table below. For the given alloy, draw the solid concentration curve that will occur in the equilibrium state and Scheil solidification curve along the length of the rod. (Draw the phase diagram for the indicated alloy using Thermo- Calc software and use the necessary values from this diagram.) Al-13(wt.%)cu Solid Liquid 4. Repeat the 3rd question using Thermo-Calc software and compare the results obtained with Thermo-Calc and those found in the 3rd question. Clearly specify the Thermo-Calc procedure and include relevant diagrams and screenshots. 5. Based on the composition changes in the solid and/or liquid, draw at least 3 different representative microstructures for the alloy provided to you, considering equilibrium and Scheil solidification results (i.e. at points such as solid+liquid at high temperature, solid+liquid at lower temperature, and at room temperature). Compare these microstructures.
Expert Answer:
Answer rating: 100% (QA)
Solutions Step 1 Step 1 Understanding the ThermoCalc Software Procedure for Al13 wt Cu Alloy Explanation Launch ThermoCalc Software Open the ThermoCal... View the full answer
Related Book For
Posted Date:
Students also viewed these mechanical engineering questions
-
a. Example 13-1: Batch Reactor with an Exothermic Reaction Wolfram 1. Adiabatic Case: Use Wolfram to see whether you can find a trajectory that is ready to ignite and whose trajectory looks like a...
-
What am I required to do in this assignment? Shared Power is an information system to help tradesmen share expensive and specialist tools rather than buying them themselves. Registered owners add...
-
Verify that A and AÌ = p -1 AP have the same spectrum. 19 4 2 12 1 P.
-
For the machine element shown, locate the z coordinate of the center of gravity. 1.5 in:- ,75 in. 1.5 in. 2.25 in 1.5 in. r= 0.95 in. r=0.95 in. 0.5 in 5 in 1.5 in.
-
Colorado Mining paid $600,000 to acquire a mine with 40,000 tons of coal reserves. The following statements model reflects Colorado Minings financial condition just prior to purchasing the coal...
-
Which of the following organizations write accounting rules? (a) FASB and Congress. (b) EDGAR and IASB. (c) FASB, SEC, and IASB. (d) SOX, SEC, and IASB.
-
Suppose that Trent and Xavier discover that Brad took the idea of Hallowed and sold it to the company that produced Halo 2. Which type of intellectual property issue does this raise? Two computer...
-
Scribners Corporation produces fine papers in three production departments-Pulping, Drying, and Finishing. In the Pulping Department, raw materials such as wood fiber and rag cotton are mechanically...
-
Consider the following state of a system with four processes, P1, P2, P3, and P4, and five types of resources, RS1, RS2, RS3, RS4, and RS5: Using the deadlock detection algorithm described in Section...
-
1. It is desired to finish the design of a leveler of a mechanical system, which is in the concept stage, which indicates that it does not have final dimensions, as indicated in figure 1. Where it...
-
Find the indefinite integral. (Remember the constant [15 (sin(x) 8 cos(x)) dx
-
Suppose that a particle has a displacement s at time t given by the equation s = 3t + 2 ti 3? What is the value of the acceleration of the particle at time t = Give your answer correct to two decimal...
-
Consider the below selected financial information. What were the amount of dividends paid during 2020? Net Income Cash Accounts Receivable Inventory Accounts Payable Long-Term Debt 2019 20 75 150 80...
-
). lim (-7e-2+4) Evaluate lim (-7e7 Provide your answer below: Enter an exact answer.
-
Penn Corp. is analyzing the possible acquisition of Teller Company. Both believes the acquisition will increase its total aftertax annual cash flow by $922,173.42 indefinitely. The current market...
-
3 4 Let T = 4. 1 13 0 The range of T is (x, y, 2), where r, y, z must satisfy the equation
-
How does the organizational structure of an MNC influence its strategy implementation?
-
The paper Teens and Distracted Driving (Pew Internet & American Life Project, 2009) reported that in a representative sample of 283 American teens ages 16 to 17, there were 74 who indicated that they...
-
A medical research team wishes to evaluate two different treatments for a disease. Subjects are selected two at a time, and one is assigned to Treatment 1 and the other to Treatment 2. The treatments...
-
In a study of academic procrastination, the authors of the paper Correlates and Consequences of Behavioral Procrastination (Procrastination, Current Issues and New Directions [2000]) reported that...
-
Consider a plane truss in figure 1.31. The horizontal and vertical members have length \(l\), while inclined members have length \(\sqrt{2} l\). Assume Young's modulus \(E=100 \mathrm{GPa}\), cross...
-
Solve the nodal displacements and element forces of the plane truss problem in figure 1.23. Use the following numerical values: \(A E=10^{7} \mathrm{~N}, L=1 \mathrm{~m}, \alpha=10^{-5} /{ }^{\circ}...
-
The shape functions of a linear 3node element are also called barycentric or area coordinates because they uniquely define the location of a point in the triangle. Show that the shape functions in...
Study smarter with the SolutionInn App