B 4 2 F 1.000- .75- 3.00 A 2. BREAK ALL SHARP EDGES 1. INTERPRET DIMENSIONS...

Transcribed Image Text:

B 4 2 F 1.000- .75- 3.00 A 2. BREAK ALL SHARP EDGES 1. INTERPRET DIMENSIONS & TOLERANCES ACCORDING TO ANSI Y14.5M - 2009 NOTES: Penn State Erie The Behrend College 1 ZONE REV REVISION HISTORY DESCRIPTION DATE APPROVED K A DIM WAS 2.00 8/4/2015 D.L. .50 H B A 1.75 ANGLE BLOCK UNSPECIFIED TOLERANCES 2-PL DEC. = 0.02 EDSGN 100 3-PL DEC. = 0.005 DRILLED HOLES = +0.010, -0.002 ANGLES = 0 30' MATERIAL: CRS 2 4 .65 E D A .70- -.40 G 1.50- 30 C DWN BY: D. LEWIS SCALE DATE: 1:1 8/3/2015 DWG NO 1 A-15-BR001 B A What method was used to dimension the inclined plane on the side of the Angle Block? Angular Horizontal Radius Coordinate Question 2 The dimensions on this drawing are interpreted according to the standard. 0.25 What is the tolerance on the 0.40 dimension? +0.010, -0.002 0.02 0 30' 0.005 Question 4 How many hidden lines would be in the REAR (back) view of the part? 4 0.25 pts The scale of this drawing is what? Half (1:2) Fifth (1:5) Double (2:1) Full (1:1) Question 6 How many hidden lines would be in the BOTTOM view of the part? O 1 2 3 4 0.25 pts The material of the part detailed on this drawing is look it up (but it's not graphite). Question 8 What is the tolerance on the angular dimension? 0.005 + 0 30' 0.02 1 Note: you can use google to 0.25 pts What three views are shown on the drawing? Front Left Auxiliary Top Bottom Back Right Section What does the line under the 1.75 dimension mean? The dimension is not to scale. The dimension is a reference dimension. The dimension is important. O The dimension is incorrect. Before revision A, dimension B had a value of... Give answer to 2 decimal places. Question 12 What does the symbol shown here represent? The view is an Auxiliary view. There was a revision. It is a warning. This is the first of a series of drawings. Dimension G has a value of... Give answer to 1 decimal place. Question 14 Dimension B has a value of... Give answer to 1 decimal place. Question 15 Dimension I has a value of... Give answer to 1 decimal place. Dimension E has a value of... Give answer to 1 decimal place. Question 17 Dimension J has a value of... Give answer to 1 decimal place. Question 18 Dimension F has a value of... Give answer to 2 decimal places. Dimension K has a value of... Give answer to 1 decimal place. Question 20 Dimension D has a value of... Give answer to 1 decimal place. Question 21 Dimension L has a value of... Give answer to 1 decimal place. Dimension H has a value of... Give answer to 3 decimal places. B 4 2 F 1.000- .75- 3.00 A 2. BREAK ALL SHARP EDGES 1. INTERPRET DIMENSIONS & TOLERANCES ACCORDING TO ANSI Y14.5M - 2009 NOTES: Penn State Erie The Behrend College 1 ZONE REV REVISION HISTORY DESCRIPTION DATE APPROVED K A DIM WAS 2.00 8/4/2015 D.L. .50 H B A 1.75 ANGLE BLOCK UNSPECIFIED TOLERANCES 2-PL DEC. = 0.02 EDSGN 100 3-PL DEC. = 0.005 DRILLED HOLES = +0.010, -0.002 ANGLES = 0 30' MATERIAL: CRS 2 4 .65 E D A .70- -.40 G 1.50- 30 C DWN BY: D. LEWIS SCALE DATE: 1:1 8/3/2015 DWG NO 1 A-15-BR001 B A What method was used to dimension the inclined plane on the side of the Angle Block? Angular Horizontal Radius Coordinate Question 2 The dimensions on this drawing are interpreted according to the standard. 0.25 What is the tolerance on the 0.40 dimension? +0.010, -0.002 0.02 0 30' 0.005 Question 4 How many hidden lines would be in the REAR (back) view of the part? 4 0.25 pts The scale of this drawing is what? Half (1:2) Fifth (1:5) Double (2:1) Full (1:1) Question 6 How many hidden lines would be in the BOTTOM view of the part? O 1 2 3 4 0.25 pts The material of the part detailed on this drawing is look it up (but it's not graphite). Question 8 What is the tolerance on the angular dimension? 0.005 + 0 30' 0.02 1 Note: you can use google to 0.25 pts What three views are shown on the drawing? Front Left Auxiliary Top Bottom Back Right Section What does the line under the 1.75 dimension mean? The dimension is not to scale. The dimension is a reference dimension. The dimension is important. O The dimension is incorrect. Before revision A, dimension B had a value of... Give answer to 2 decimal places. Question 12 What does the symbol shown here represent? The view is an Auxiliary view. There was a revision. It is a warning. This is the first of a series of drawings. Dimension G has a value of... Give answer to 1 decimal place. Question 14 Dimension B has a value of... Give answer to 1 decimal place. Question 15 Dimension I has a value of... Give answer to 1 decimal place. Dimension E has a value of... Give answer to 1 decimal place. Question 17 Dimension J has a value of... Give answer to 1 decimal place. Question 18 Dimension F has a value of... Give answer to 2 decimal places. Dimension K has a value of... Give answer to 1 decimal place. Question 20 Dimension D has a value of... Give answer to 1 decimal place. Question 21 Dimension L has a value of... Give answer to 1 decimal place. Dimension H has a value of... Give answer to 3 decimal places.