1. Set up the following topology in packet tracer 2960 24TT Swach1 PC-PT PCO 2. Configure...

   

Transcribed Image Text:

1. Set up the following topology in packet tracer 2960 24TT Swach1 PC-PT PCO 2. Configure PCO as shown below PCavure OCHCE PA Physics Carto De Peogramming Defau Server Penguran O DOP PA Le Local Add Paway POS Server 802.1X Authentication Fes Securty Se ⒸAC 102 108.12 255256250 0000 Completed 2911 RouterO Static FE80 290 291 ES.COM Completed 2960 24TT PC-PT PC1 3. Repeat the previous step for PC1 giving it a different IP address so it is assigned to the 19.168.2.0 Completed 4. Now assign IP addresses to both GigabitEthernet0/0 interfaces on the router. You can the use GUI or the command line. 5. Attempt to ping PC1 from PC0. Completed What happened? Why didn't the ping work? 6. On PCO, enter in the default gateway as the IP address you set for Gigabit Ethernet0/0. PCO Physical Config Desktop Programming Attributes P Configuration Interface IP Configuration ⒸDHCP P Address Subnet Mask Defaut Gateway DNS Server IPv6 Configuration O DHCP Pv6 Address Link Local Address Pv6 Gateway Pv6 DNS Server 802.1X Authentication Username Тор FastEtherneto Use 802.1x Security Static 192.168.1.2 255 255.255.0 192.168.1.1 10.000 Auto ConfigStatic MOS FE80 290:2BFF FEBS CB36 Completed x 7. Repeat the same step for PC1 and GigabitEthernet0/1, that you did for PC0 in step 6. Completed X 8. Attempt to ping PC1 from PC0 again. Did it work? It should be a "yes" If not........start troubleshooting Ⓒ 9. Attach a screenshot of your successful ping below 1. Set up the following topology in packet tracer 2960 24TT Swach1 PC-PT PCO 2. Configure PCO as shown below PCavure OCHCE PA Physics Carto De Peogramming Defau Server Penguran O DOP PA Le Local Add Paway POS Server 802.1X Authentication Fes Securty Se ⒸAC 102 108.12 255256250 0000 Completed 2911 RouterO Static FE80 290 291 ES.COM Completed 2960 24TT PC-PT PC1 3. Repeat the previous step for PC1 giving it a different IP address so it is assigned to the 19.168.2.0 Completed 4. Now assign IP addresses to both GigabitEthernet0/0 interfaces on the router. You can the use GUI or the command line. 5. Attempt to ping PC1 from PC0. Completed What happened? Why didn't the ping work? 6. On PCO, enter in the default gateway as the IP address you set for Gigabit Ethernet0/0. PCO Physical Config Desktop Programming Attributes P Configuration Interface IP Configuration ⒸDHCP P Address Subnet Mask Defaut Gateway DNS Server IPv6 Configuration O DHCP Pv6 Address Link Local Address Pv6 Gateway Pv6 DNS Server 802.1X Authentication Username Тор FastEtherneto Use 802.1x Security Static 192.168.1.2 255 255.255.0 192.168.1.1 10.000 Auto ConfigStatic MOS FE80 290:2BFF FEBS CB36 Completed x 7. Repeat the same step for PC1 and GigabitEthernet0/1, that you did for PC0 in step 6. Completed X 8. Attempt to ping PC1 from PC0 again. Did it work? It should be a "yes" If not........start troubleshooting Ⓒ 9. Attach a screenshot of your successful ping below

Answer rating: 100% (QA)

I can provide guidance on your networking tasks but I cannot set up Packet Tracer or view screenshots However I can help you understand the steps to complete your tasks and troubleshoot any issues Her... View the full answer