The motor supplies 11.1 kW at 19.9 Hz at A. The bearings shown permit free rotation...
Fantastic news! We've Found the answer you've been seeking!
Question:
Transcribed Image Text:
The motor supplies 11.1 kW at 19.9 Hz at A. The bearings shown permit free rotation of the shafts. Assume Ng=44 teeth and Ne=28 teeth. (a) Shaft (2) is a solid 36-mm-diameter steel shaft. Determine the maximum shear stress T2 produced in shaft (2). (b) If the shear stress in shaft (1) must be limited to 43 MPa, determine the minimum acceptable diameter d, for shaft (1) if a solid shaft is used. Ng В (1) Nc Tp (2) Answers: MPa. (a) T2 = mm. (b) di = The motor supplies 11.1 kW at 19.9 Hz at A. The bearings shown permit free rotation of the shafts. Assume Ng=44 teeth and Ne=28 teeth. (a) Shaft (2) is a solid 36-mm-diameter steel shaft. Determine the maximum shear stress T2 produced in shaft (2). (b) If the shear stress in shaft (1) must be limited to 43 MPa, determine the minimum acceptable diameter d, for shaft (1) if a solid shaft is used. Ng В (1) Nc Tp (2) Answers: MPa. (a) T2 = mm. (b) di =
Expert Answer:
Answer rating: 100% (QA)
Step 1 Net for que in shaft I on geer B Tiz Po Ti Tez 111x 03 8877 NM Tor qu... View the full answer
Related Book For
Posted Date:
Students also viewed these abstract writing questions
-
Determine the maximum shear stress in the strut if it is subjected to a sheer force of V = 20 kN. 12 mm 60 mm 12 mm 20 mm 80 mm 20 mm
-
Determine the maximum shear stress acting at section aa of the cantilevered strut. 4 kN 2 kN 300 mm 250 mm 250 mm 20 mm 70 mm 20 mm 50 mm
-
Determine the maximum shear stress acting at section aa in the beam. 8000 lb 150 lb/ft B. 4 ft 4 ft 1.5 ftT1.5 ft
-
Miller with corporate and personal taxes ____________. Answer options are displayed below it. After Modigliani and Miller's (MM) original no-tax theory, they went on to develop another theory that...
-
What kinds of information must the organizers of new national banks provide the Comptroller of the Currency in order to get a charter? Why might this required information be important?
-
The cantilever bracket is bolted to a column with three M12 Ã 1.75 ISO 5.8 bolts. The bracket is made from AISI 1020 hot-rolled steel. Find the factors of safety for the following failure...
-
Which of the following indicates a satisfactory situation from the viewpoint of good internal control? (a) The cashier reports to the treasurer. (b) Payroll accounting reports to the controller. (c)...
-
As the most senior member of the team present, what can you do to convince Lou and Stan about the importance of testing the accounting module with live data? What can systems analysts do in planning...
-
Because of fragmentation, an IP datagram can arrive in several pieces, not necessarily in the correct order. The IP entity at the receiving end system must accumulate these fragments until the...
-
A beam ABCD with a vertical arm CE is supported as a simple beam at A and D (see figure). A cable passes over a small pulley that is attached to the arm at E. One end of the cable is attached to the...
-
2) Consider this game. (A's payoff, B's payoff) U (1,1) (1,-1) A U" U' (2,3) D B D" D' U" (2,1) D" (1,0) a) Find the backward induction outcome of the game. b) Write the strategies available for each...
-
What are the implications for global labor markets and income inequality, and how can international policy frameworks be designed to address these emerging challenges while promoting innovation and...
-
How do cultural and religious differences contribute to international tensions, and what role can international diplomacy and cross-cultural dialogue play in fostering mutual understanding and...
-
What is the impact of global health disparities on the effectiveness of international efforts to combat pandemics, and what steps can be taken to promote equitable access to healthcare resources and...
-
How can international agreements and treaties be designed to effectively address cross-border environmental issues, such as air and water pollution, given the varying levels of commitment and...
-
On January 1, 20x1, ABC, Inc. sold a $480 snow blower with a $120 extended warranty. The warranty covers three years of repairs. Assuming the costs are incurred evenly over the warranty, How much...
-
Given the Following Circuit where I = 16 A, R = 4.5 MQ, and R = 3.7 MQ, find the branch current I in A. R2 Vs Answer:
-
TRUE OR FALSE: 1. Banks with a significantly large share of fixed-interest rate home loans are less exposed to interest rate risks. 2. Although Australian banks are pretty big, they are not...
-
The beam is made of elastic perfectly plastic material. Determine the maximum elastic moment and the plastic moment that can be applied to the cross section. Take Ï Y = 36 ksi. 1.5 in! 3 in.....
-
The copper pipe has an outer diameter of 3 in. and an inner diameter of 2.5 in. If it is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown, determine the...
-
Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal stress. Specify the orientation of the element in each case. A 200 MPa 100 MPa - 150 MPa
-
Use the health expenditure data of Section 16.6. The model is a probit regression of DMED, an indicator variable for positive health expenditures, against the 17 regressors listed in the second...
-
Suppose we obtain a kernel density estimate using the uniform kernel (see Table 9.1) with \(h=1\) and a sample of size \(N=100\). Suppose in fact the data \(x \sim \mathcal{N}[0,1]\). (a) Calculate...
-
Suppose we obtain a kernel regression estimate using a uniform kernel (see Table 9.1) with \(h=1\) and a sample of size \(N=100\). Suppose in fact the data \(x \sim \mathcal{N}[0,1]\) and the...
Study smarter with the SolutionInn App