Pin fins are to be specified for use in an industrial cooling application. The fins will be
Question:
Pin fins are to be specified for use in an industrial cooling application. The fins will be subjected to a gas in cross flow at V = 10 m/s. The cylindrical fin has a diameter of D = 15 mm, and the cross-sectional area is the same for each configuration shown in the sketch.
For fins of equal length and therefore equal mass, which fin has the largest heat transfer rate? Assume the gas properties are those of air at T = 350 K.
= V,T_ Configuration A V.T_ Configuration B V.T Configuration C
Step by Step Answer:
There are a few things to consider when answering this question The first is the shape of the fin Th...View the full answer
Fundamentals Of Heat And Mass Transfer
ISBN: 9780470501979
7th Edition
Authors: Theodore L. Bergman, Adrienne S. Lavine, Frank P. Incropera, David P. DeWitt
Related Video
An air pump is a device used to inflate or deflate objects by moving air in or out of them. There are many different types of air pumps, ranging from manual hand pumps to electrically powered pumps, and they are used for a variety of purposes. John had trouble blowing up many balloons without a balloon pump and experienced pain. He solved this problem by using an empty plastic bottle with a rectangular-shaped hole in the cap, a cut piece of balloon stretched over it, and a small hole in the bottle. By pressing and releasing the bottle, he created an air pump to inflate the balloons without any discomfort. Air pumps utilize fluid mechanics and thermodynamics principles to increase air pressure inside an object being inflated, such as a bicycle tire. The ideal gas law is used to calculate the pressure inside the tire. As air pressure increases, the object becomes more rigid and can support more weight. The efficiency of the pump is determined by how much of the work done is converted into useful work, such as inflating the tire, and how much is lost as heat. Understanding these principles is important to effectively use and optimize the use of air pumps.
Students also viewed these Physics questions
-
Circular aluminum fins are to be attached to the tubes of a heating system. The increase in heat transfer from the tubes per unit length as a result of adding fins is to be determined.
-
A pipe, cross sectional area 0.1 m2, carries a flow of 75% O2 and 25% N2 by mole with a velocity of 25 m/s at 200 kPa, 290 K. To install and operate a mass flow meter it is necessary to know the...
-
A pipe, cross sectional area 0.1 m2, carries a flow of 75% O2 and 25% N2 by mole with a velocity of 25 m/s at 200 kPa, 290 K. To install and operate a mass flow meter it is necessary to know the...
-
Create a use case diagram that would illustrate the use cases for the following dentist office system: Whenever new patients are seen for the first time, they complete a patient information form that...
-
Using the same information presented in E18-1, complete the following requirements assuming that the lessor and lessee are following IFRS: In E18-1 On January 1, the Robinson Sales Company entered...
-
Jonas, Teese, and Moyer are liquidating their partnership. Before selling the noncash assets and paying the liabilities, the Capital balances are Jonas, $57,500; Teese, $34,500; and Moyer, $23,000....
-
\(P(60
-
Top Corporation produces a line of beverage lids. The production process has been automated, so the product can now be produced in one operation rather than in the three operations that were needed...
-
Inventories are valued on a lower of last-in, first-out (LIFO)cost or market basis. At December 31, 2022 and 2021, inventorieswould have been greater by $2.1 million and $1.9 million,respectively, 2...
-
Chris Guthrie was recently hired by S&S Air, Inc., to assist the company with its financial planning, and to evaluate the company's performance. Chris graduated from college five years ago with a...
-
In a manufacturing process, long aluminum rods of square cross section with d = 25 mm are cooled from an initial temperature of T i = 400C. Which configuration in the sketch should be used to...
-
An L = 1-m-long vertical copper tube of inner diameter D i = 20 mm and wall thickness t = 2 mm contains liquid water at T w 0C. On a winter day, air at V = 3 m/s, T =20C is in cross flow over the...
-
Yang Inc. reports under IFRS and has adopted the policy of classifying interest received as an investing activity. During 2023, Yang lent $30,000 to a key supplier in exchange for a two-year...
-
Describe the variation of absorption cross sections with neutron energy for thermal neutron energies (E <1eV).
-
Calculate a cost ratio for the following: Note: Round your answer to the nearest cent. Cost of goods available for sale at cost: $47,123 Cost of goods available for sale at retail: $55,605 Cost ratio
-
A 1 5 0 - mm - diameter shaft with a mass of 2 0 kg is rotating at 9 0 0 rpm . A pulley mounted on the shaft has a mass moment of inertia of 0 . 1 5 kg m 2 . If the shaft and the pulley coast to a...
-
In this milestone, you will submit drafts of completed tax forms for the client described in the final project data sheet. You will submit these forms to support your client recommendations in the...
-
Molly wants to clear her remaining stock in preparation for ordering a new line of products to sell. As a result, she's willing to increase her CPA (cost-per-acquisition) and investment, as long as...
-
Following is an inventory acquisition schedule for Weaver Corp. for 2012: Units Unit Cost Beginning inventory............5,000...............$10 Purchase: February...
-
Find the velocity, acceleration, and speed of a particle with the given position function. r(t) = (t 2 , sin t - t cos t, cos t + t sin t), t > 0
-
The bottom half of an I-beam providing support for a furnace roof extends into the heating zone. The web is well insulated, while the flange surfaces experience convection with hot gases at T . =...
-
Consider one-dimensional conduction in a plane composite wall. The exposed surfaces of materials A and B are maintained at T 1 = 600 K and T 2 = 300 K respectively. Material A, of thickness L a = 20...
-
A platen of thermal conductivity k = 15 W/m K is heated by flow of a hot fluid through channels of width L = 20mm, with T ,i = 200C and hi = 500W/m 2 K. The upper surface of the platen is used to...
-
K Chapter 8 Video_Organizations and Information Systems 5.10 mins As Sue explains in this video, the application approval process needed to be redesigned for all the following reasons EXCEPT A. the...
-
Draw an ER Diagram for this question. Each employee in a company must take at least one training course. An employee could take many training courses. A training course may be taken by many employees...
-
The prices by which the government buys food grain for the maintenance of the public distribution system and to build a buffer stock are known as , A . Minimum Support Price B . Procurement Price C ....
Study smarter with the SolutionInn App