The figure below represents a schematic of pipe network. A rate of 35 Ls, is pumped...
Fantastic news! We've Found the answer you've been seeking!
Question:
Transcribed Image Text:
The figure below represents a schematic of pipe network. A rate of 35 Ls, is pumped to feed two lines (3-4-5-6; and 2-7-8). The length and diameter of each pipe segment are listed in the table. Assume the friction factor of the two lines are equal (f456f278), determine: (1) the total pressure loss through the pipe network, (ii) the power of the pump required to overcome the friction loss along the system. The viscosity and density of the water are respectively: 0.0015 Pa.s; 985 kg/m³. Use the following expression to evaluate the friction factor with roughness ratio (@D-0.025): √ [6+(3/9)¹] Re -1.8 log Pump 1 2 7 Pipe section 1-2 3-4-5-6 2-7-8 6 Length (m) Diameter (cm) 30 17 25 40 34 30 The figure below represents a schematic of pipe network. A rate of 35 Ls, is pumped to feed two lines (3-4-5-6; and 2-7-8). The length and diameter of each pipe segment are listed in the table. Assume the friction factor of the two lines are equal (f456f278), determine: (1) the total pressure loss through the pipe network, (ii) the power of the pump required to overcome the friction loss along the system. The viscosity and density of the water are respectively: 0.0015 Pa.s; 985 kg/m³. Use the following expression to evaluate the friction factor with roughness ratio (@D-0.025): √ [6+(3/9)¹] Re -1.8 log Pump 1 2 7 Pipe section 1-2 3-4-5-6 2-7-8 6 Length (m) Diameter (cm) 30 17 25 40 34 30
Expert Answer:
Answer rating: 100% (QA)
Given Flow rate Q 35 Ls Viscosity 00015 Pas Density 985 kgm3 Roughness ratio D 0025 Pipe diameters a... View the full answer
Related Book For
Posted Date:
Students also viewed these accounting questions
-
Discuss which organizational structure (i.e. functional, product-market divisional, matrix) you would recommend Guelph General Hospital implement, assuming the hospital moves forward with the...
-
Safe Emergency Evacuation of Staff and Customers. Find and read the 'Salford College Emergency Plan for your area and check it for any errors and fill in the required sections on the template...
-
d) Joy Company manufactures a high quality pipes in two departments: 1 and 2 Materials are introduced at various points during work in department 1. After products in department I are completed, the...
-
If we define the median of a sequence as a number so that exactly as many elements come before it in the sequence as come after it, fix the program in 4.6.3 so that it always prints out a median....
-
Electronic Innovators is the defendant in a $10 million lawsuit filed by one of its customers, Aviation Systems. The litigation is in final appeal, and legal counsel advises that it is probable that...
-
Question 3 1. ABC Steel is a steel manufacturing company, it has been discovered that the company produces high scrap and have been experiencing high production lead times. Given the above case...
-
Potato skins are generated as a by-product in making potato chips and frozen hash browns at Fit Food. The skins are sold to restaurants for use in appetizers. Processing and disposal costs associated...
-
This is really an odd situation, said Jim Carter, general manager of Highland Publishing Company. We get most of the jobs we bid on that require a lot of press time in the Printing Department, yet...
-
You should work on : DHL, Bonn, Germany https://www.dhl.com/ Your group report should be between 750 and 1,000 words (excluding cover page and reference page). Include the following information in...
-
For this assignment, we are going to change our point of view. You are now working for Woolly, and you are preparing Woolly's response to Mammoth's RFP to support the transition of the 12 staff from...
-
4) A ladder of mass m is leaning against a wall, held in place by a string, connected between the wall and the ladder, as shown. Both the wall and ground are frictionless. Which of the answers...
-
Problem 5. Wages of manual workers in a large industry have a bell-shaped distribution with a mean value of 1,500 dirhams per week with a standard deviation of 150 dirhams. a. (1.5 points) What...
-
if an asset manager short sells 1097 shares of British tobacco at R348 per share. what would the value of a stop buy order need to be in order to limit potential losses to R75 000
-
Explain the influence of investor psychology on risk tolerance and investment choices. Explain briefly.
-
Ali Redha Co. needs $5,000,000 for new investment projects. The company has a target capital structure (D/E) of two-third (2/3). If Ali Redha Co. net income is $ 4,000,000, what is the amount of...
-
A firms debt to equity ratio is 1.0. The before tax cost of debt=7%, RF=3%, beta=1.1, the market return =8% and the tax rate =32%. The firm's WACC (weighted average cost of capital)=?% Use 4 decimals...
-
l folder. Pick three tools from the following tools and explain how market-oriented firms utilize these tools to understand the competition and customer behavior. a) As products, a celebrity might be...
-
What are the two methods used to translate financial statements and how does the functional currency play a role in determining which method is used?
-
A certain reaction has the following general form: aA bB At a particular temperature and [A] 0 = 2.80 10-3 M, concentration versus time data were collected for this re-action, and a plot of 1/[A]...
-
A 4.72- g sample of methanol (CH3OH) was placed in an otherwise empty 1.00- L flask and heated to 250oC to vaporize the methanol. Over time the methanol vapor decomposed by the following reaction:...
-
When organic compounds containing sulfur are burned, sulfur dioxide is produced. The amount of SO 2 formed can be determined by reaction with hydrogen peroxide: H 2 O 2 (aq) + SO 2 (g) H 2 SO 4 (aq)...
-
Which of the following is usually not found on a job order cost sheet? a. Manufacturing overhead b. Finished units currently on hand c. Direct materials d. Unit cost Never
-
Which of the following is not one of the categories of cost involved in the allocation of service department costs? a. Service department costs allocated to production departments b. Costs directly...
-
Which of the following would be a reason for choosing to use departmental overhead rates, instead of a single company-wide overhead rate? a. Each departments overhead is structured very different...
Study smarter with the SolutionInn App