The car rests on four scales and in this position the scale readings of both the front
Question:
The car rests on four scales and in this position the scale readings of both the front and rear tires are shown by FA and FB. When the rear wheels are elevated to a height of 3 ft above the front scales, the new readings of the front wheels are also recorded. Use this data to compute the location x and y to the center of gravity G of the car. The tires each have a diameter of 1.98ft.
9.40 ft- = 1129 lb + 1168 Ib = 2297 lb FA Fr = 975 Ib + 984 lb = 1959 lb 3.0 ft = 1269 lb + 1307 Ib = 2576 lb FA
Step by Step Answer:
In horizontal positio...View the full answer
Related Video
Take 2 forks and place them on one another in such a way that we can place the coin in between the prongs. Now try to place the coin with forks on the edge of the glass. It will take you some time to adjust the coin on the edge. This requires a little practice to adjust the coin on the edge of the glass. With a little effort, we will see the coin sitting on the edge calmly. If you look closely you will see it wobbling a little bit. The mass is in the handles of the forks so as a low center of mass it stables as it looks.
Students also viewed these Civil Engineering questions
-
A 1500-kg car rests on four tires, each of which is inflated to a gauge pressure of 200kPa. What is the area of contact of each tire with the road, if the four tires support the weight equally?
-
The parking brake on a car causes the rear wheels to lock up. What would be the likely consequence of applying the parking brake in a car that is in rapid motion?
-
To determine the location of the center of gravity of the automobile it is first placed in a level position, with the two wheels on one side resting on the scale platform P. In this position the...
-
If you were in charge of B&D, indicate the possible decisions you might take as regards the four Ps and the points you would want to keep in mind as you go about the task of marketing for...
-
Reread the Management Focus on DMG-Shanghai. Then, answer the following questions a. Why do you that it is so important to cultivate guanxi and guanxiwang in China? b. What does the experience of DMG...
-
An experiment has run a single replicate of a 2 4 design and calculated the following factor effects: (a) Construct a normal probability plot of the effects. (b) Identify a tentative model, based on...
-
A temperature sensor of \(10.5-\mathrm{mm}\) diameter experiences cross flow of water with a free stream temperature of \(80^{\circ} \mathrm{C}\) and variable velocity. Derive an expression for the...
-
After extensive research and development, Good-week Tires Inc. has recently developed a new tire, the Super Tread, and must decide whether to make the investment necessary to produce and market it....
-
Oriole Company has the following production data for selected months. Ending Work in Process Beginning Month Work in Process Units Transferred Out % Complete as to Units Conversion Cost January -0-...
-
Wendy and Frank Cotroni, ages 30 and 35, plan to purchase life insurance. Wendy does not have any coverage, while Frank has a $150 000 policy at work. The Cotronis have two children, ages three and...
-
The composite plate is made from both steel (A) and brass (B) segments. Determine the mass and location (x, y, z) of its mass center G. Take st = 7.85 Mg/m3 and br = 8.74Mg>m3. 225 mm 150 mm 150 mm...
-
Uniform blocks having a length L and mass m are stacked one on top of the other, with each block overhanging the other by a distance d, as shown. If the blocks are glued together, so that they will...
-
Fig. 6.61 shows an alternate scheme for biasing the NE5234 output stage . Ignoring all base currents, find |I C74 | I C75 . Use Fig. 6.42 for the relative emitter areas of all the transistors except...
-
For a single-phase, two-wire line consisting of two solid cylindrical conductors of same radius, \(r\), the total circuit inductance, also called loop inductance, is given by (in \(\mathrm{H} /...
-
Design a cosine-modulated filter bank with \(M=5\) sub-bands and at least \(40 \mathrm{~dB}\) of stopband attenuation.
-
Two small, irregularly shaped conducting objects, one carrying charge \(+q\) and one carrying charge \(-q\), are placed on an \(x\) axis at \(x=-4.0 \mathrm{~m}\) and \(x=+4.0 \mathrm{~m}\),...
-
Mr Chai has been trading for some years as a wine merchant. The following list of balances has been extracted from his ledger as at 30 April 2010, the end of his most recent financial year. The...
-
Resistor Ltd manufactures electrical units. All units are identical. The following information relates to June and July Year 5. (a) Budgeted costs and selling prices were: (b) Actual production and...
-
What is synergy? What are the sources of synergy? Give examples. Why is it so elusive?
-
Define the essential properties of the following types of operating systems: a. Batch b. Interactive c. Time sharing d. Real time e. Network f. Parallel g. Distributed h. Clustered i. Handheld
-
If you were a defendant in a criminal case, which personal characteristics would you want jurors to have? Why?
-
Determine the angle between the two cables. 2 m 3 m F = 40 N |A Z F = 70 N 3 m 4m -3 m- 2m B
-
Determine the magnitude of the projected component of force F along the pole. F = (-20i + 50j - 10k} lb A 6 ft 1-281- X 3 ft Prob. 2-105
-
Determine the angles between the wire segments. X -0.6 m- N -0.4 m- Prob. 2-104 0.2 m B 0.8 m 0.5 m
-
Image transcription text Wind tunnel measurements of the pressure and skin friction around a NACA 2415 airfoil at 8 degrees angle of attack resulted in the following data of pressure and skin...
-
Image transcription text The following table contains load-extension data from a tensile test on a cylindrical specimen with gauge length 9mm and gauge diameter 5mm. Load-extension Data Load [KN] 0...
-
Image transcription text Systems Modelling and Analysis - Assignment 1 Due: Friday 25/08/2022 by 5:00:00 pm. To be submitted individually on Canvas and Gradescope. Part 1: Dartboard Positioning...
Study smarter with the SolutionInn App