Question: A 200-mm-diameter cylindrical duct and a 100 200-mm rectangular duct are to be joined as indicated. Knowing that the ducts are fabricated from the

A 200-mm-diameter cylindrical duct and a 100 × 200-mm rectangular duct are to be joined as indicated. Knowing that the ducts are fabricated from the same sheet metal, which is of uniform thickness, locate the center of gravity of the assembly.

300 s00 mm 100 mm

Step by Step Solution

★★★★★

3.52 Rating (179 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

First assume that the sheet metal is homogeneous so that the center of ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

17-E-M-E-V-M-S (401).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

The sheet-metal component shown is of uniform thickness and has a mass of 600 g. It is attached to a light axle supported by bearings at A and B located 150 mm apart. The component is at rest when it...

Two equal rectangular lots are to be enclosed by fencing the perimeter of a rectangular lot and then putting a fence across its middle. If each lot is to contain 1200 square feet, what is the minimum...

Locate the center of gravity of the sheet metal form shown. 3 in Sin r225

Using a mathematical software package of your choice you will compute a numerical solution to viscous flow through the annular region between two concentric square ducts. The parameters of the...

Please answer all parts. Thanks! Using a mathematical software package of your choice you will compute a numerical solution to viscous flow through the annular region between two concentric square...

Please complete all parts. Thanks! Using a mathematical software package of your choice you will compute a numerical solution to viscous flow through the annular region between two concentric square...

Compute the pressure drop as 0.20 m 3 /s of air flows through a three-piece 90 elbow in a 200-mm-diameter round duct.

Repeat Problem 19.21, but use a mitered elbow. Repeat Problem Compute the pressure drop as 0.20 m 3 /s of air flows through a three-piece 90 elbow in a 200-mm-diameter round duct.

In beauty salons and in homes, a ubiquitous device is the hairdryer. The front end of a typical hairdryer is idealized as a thin-walled cylindrical duct with a 6-cm diameter with a fan at the inlet...

You want to produce three 2.00-mm-diameter cylindrical wires, each with a resistance of 3.00 12 at room temperature. One wire is gold (Pg=2.44 x 10-2-m). one is copper (p. 1.72 x 102-m), and one is...

Three venture investments previously made by BKAngel, a venture investor, achieved the following outcomes for the year just completed: A. Calculate the percentage rate of return for each of the...

Economic value add equals Multiple choice question. the spread between ROE and the cost of capital divided by the capital invested in the firm. the spread between ROE and the cost of capital...

In 2018, Meghann Carlson, a single taxpayer, has QBI of $111,100 and modified taxable income of $88,880 (this is also her taxable income before the QBI deduction). Given this information, what is...

3. Let the spot interest rate be constant and positive. Verify whether the zero coupon yield curve is (a) increasing, or (b) constant, or (c) decreasing function of the maturity of the bond.

Show that f(n) = 2n is theta (n)

Technical analysts believe that one can use past price changes to predict future price changes. How do they justify this belief?

One way to find out if a wire has corroded is to measure its resistance. Explain why the resistance of a wire increases if it becomes corroded.

A 2-mm-thick piece of sheet steel is cut and bent into the machine component shown. Knowing that the density of steel is 7850 kg/m3, determine the mass moment of inertia of the component with respect...

A framing anchor is formed from 2-mm-thick galvanized steel. Determine the mass moment of inertia of the anchor with respect to each of the coordinate axes. (The density of galvanized steel is 7530...

A 0.1-in.-thick piece of sheet steel is cut and bent into the machine component shown. Knowing that the specific weight of steel is 490 lb/ft3, determine the mass moment of inertia of the component...

The piece of roof flashing shown is formed from sheet copper that is 0.8 mm thick. Knowing that the density of copper is 8940 kg/m3, determine the mass moment of inertia of the flashing with respect...

The machine element shown is fabricated from steel. Determine the mass moment of inertia of the assembly with respect to (a) The x axis, (b) The y axis, (c) The z axis. (The specific weight of steel...

The coupon rate on an issue of debt is 9% . The yield to maturity on this issue is 10% . The corporate tax rate is 35% . What would be the approximate after-tax cost of\ debt for a new issue of...