A 20 full-depth steel spur pinion has 17 teeth and a module of 1.5 mm and is

Question:

A 20◦ full-depth steel spur pinion has 17 teeth and a module of 1.5 mm and is to transmit 0.25 kW at a speed of 400 rev/min. Find an appropriate face width if the bending stress is not to exceed 75 MPa.

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Shigleys Mechanical Engineering Design

ISBN: 978-1121345317

9th edition

Authors: Richard G. Budynas, J. Keith Nisbett

See More Books

Question Posted: Oct 30, 2009 01:21 AM

See More Questions

A 20 full-depth steel spur pinion has a diametral pitch of 5 teeth/in and 24 teeth and transmits 6 hp at a speed of 50 rev/min. Find an appropriate face width if the allowable bending stress is 20...
A 20 full-depth steel spur pinion has 20 teeth and a module of 2 mm and is to transmit 0.5 kW at a speed of 200 rev/min. Find an appropriate face width if the bending stress is not to exceed 75 MPa.
A steel spur pinion has a module of 1 mm and 16 teeth cut on the 20 full-depth system and is to carry 0.15 kW at 400 rev/min. Determine a suitable face width based on an allowable bending stress of...
A hollow-fiber membrane device is operated to concentrate a bacterial suspension. The flow rate of cell suspension into the fibers is 350 kg/min. The inlet cell suspension is comprised of 1.0 wt%...
What is an information system? What are some of the ways information systems are changing our lives?
(Roberts7) A city is divided into 3 areas 1, 2, and 3. It is estimated that amounts u1, u2, and u3 of pollution are emitted each day from these three areas. A fraction qij of the pollution from...
12. Mildred Pirelli supervises salespeople in a department store. One day she walked around her department to observe the salespeople in action. She saw a salesperson approve a charge card purchase...
Mop and Broom Manufacturing estimates that it takes 4.5 hours for each broom to be produced, from raw materials to final product. An evaluation of the process reveals that the amount of time spent...
* What are good options to consider in regard to rewarding workers for good performance when raises are not feasible? Target pay increases to poorer performing employees to increase their job...
A county chairwoman of a certain political party is making plans for an upcoming presidential election. She has received the services of six volunteer workers for precinct work, and she wants to...
A steel spur pinion has 15 teeth cut on the 20 full-depth system with a module of 5 mm and a face width of 60 mm. The pinion rotates at 200 rev/min and transmits 5 kW to the mating steel gear. What...
A steel spur pinion is to transmit 15 hp at a speed of 600 rev/min. The pinion is cut on the 20 full-depth system and has a diametral pitch of 5 teeth/in and 16 teeth. Find a suitable face width...
A woman is pushing a load in a wheelbarrow, as in Figure P8.44. The combined mass of the wheelbarrow and the load is 110 kg, with a center of gravity 0.25 m behind the axle. The woman supports the...
Suppose you want to model the relationship between the interest rate, the economic growth rate and the inflation rate. what would be first model to fit explain.
Question 1 [40 marks] (a) Table 1 present experimental data related to the absorbance of two compounds over a range of concentration, in a UV-Vis cell with path length I = 1.0 cm. From this table:...
i. The following table presents data on wholesale gas prices for the major capital cities in the Eastern-half of Australia, from 2011-12 to 2022-23. Use this data to construct a single, time-series...
Problem 1 Using the same Fourier-Method approach as used in lecture, consider a beam loaded as shown below. 290 -q. Cos 280 x Shane land V-280 Distributed load w = =-80 . Cos[X] a. What are the...
Think about a Floor Warden training program for that company - and write me another email (attached here as a Word document) as if I were the leader of your organization to tell me about the...
Consider a model with date0 endowmentsyh0 and date0 consumption ch0. Suppose all investors have log utility, a common discount factor , and no date1 labor income. Show that, in a competitive...
A horizontal annulus with inside and outside diameters of 8 and 10 cm, respectively, contains liquid water. The inside and outside surfaces are maintained at 40 and 20oC, respectively. Calculate the...
What are the adverse effects of excess moisture on the wood and metal components of a house and the paint on the walls?
An estimated 84 percent of enterprises now use cloud computing solutions involving multiple clouds, whereas less than 10 percent of large organizations employ just a single public cloud. Group of...
XYZ inc. was involved in a tax dispute with the national tax authority. The companys legal counsel estimates that there is a 75% likelihood that the company will lose the dispute and that the amount...
3 . Accounting.. How does depreciation impact financial statements, and what are the different methods of depreciation?

A 20 full-depth steel spur pinion has 17 teeth and a module of 1.5 mm and is

Question:

Step by Step Answer:

Eq 146b Eq 148 d 1517 255 mm Y 030...View the full answer

Shigleys Mechanical Engineering Design

Students also viewed these Mechanical Engineering questions