Question: A bolted lap joint using ISO class 5.8 bolts and members made of cold-drawn SAE 1040 steel is shown in the figure. Find the tensile

A bolted lap joint using ISO class 5.8 bolts and members made of cold-drawn SAE 1040 steel is shown in the figure. Find the tensile shear load F that can be applied to this connection to provide a minimum factor of safety of 2.5 for the following failure modes: shear of bolts, bearing on bolts, bearing on members, and tension ofmembers.

20 M20 x 2.5 40 70 40 20 80

Step by Step Solution

★★★★★

3.46 Rating (172 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Members Table A20 S 490 MPa Sy 0577490 2827 MPa Bolts Table 811 ISO class 58 S 420 M... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

233-M-E-W-B (81).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

A bolted lap joint using SAE grade 5 bolts and members made of cold-drawn SAE 1040 steel is shown in the figure. Find the tensile shear load F that can be applied to this connection if the following...

The cold-drawn AISI 1040 steel bar shown in the figure is subjected to a completely reversed axial load fluctuating between 28 kN in compression to 28 kN in tension. Estimate the fatigue factor of...

A PMOS transistor based single-stage amplifier is shown in the figure below (Fig. Q2). The PMOS has VEn = -0.7 V and a very large |VAl. +2.5 V Rs Cs Rsig Usig RD -2.5 V Fig. Q2 What is the...

The figure shows a bolted lap joint that uses SAE grade 8 bolts. The members are made of cold-drawn AISI 1040 steel. Find the safe tensile shear load F that can be applied to this connection if the...

The figure shows a bolted lap joint that uses SAE grade 5 bolts. The members are made of cold-drawn AISI 1020 steel. Find the safe tensile shear load F that can be applied to this connection to...

The figure shows a bolted lap joint that uses SAE grade 5 bolts. The members are made of hot - rolled AISI 1 0 4 0 steel. Assume the bolt threads do not extend into the joint. Find the safe tensile...

Required information Problem 0 8 . 0 6 8 - Bolts supporting a shear load The bolted connection shown in the figure uses SAE grade 8 bolts. The members are hot - rolled AISI 1 0 4 0 steel. A tensile...

The side view of a bolted connection shown in the figure is subjected to a tensile shear load of 4 9 0 kN . It is required that the bolts should be aligned in three rows. The front view is in a...

Problem 2 The side view of a bolted connection shown in the figure is subjected to a tensile shear load of 4 9 0 kN . It is required that the bolts should be aligned in three rows. The front view is...

A. From the following list, identify each item as operating (O), investing (I), financing (F), or not separately reported on the statement of cash flows (N). Purchase of land Proceeds from sale of...

What other issues of merger integration may arise?

The diagram shows two shapes, P and Q. Choose the column vector (A, B or C) that translates 35 432 P 1 0 1 2 3 4 5 6 x

State the meaning and feature of employee welfare?

Suppose that xx = 2,500 yy = 5,200 xy = 3,700 and the z-direction shear stresses (zx, zy) are zero, while the z-direction normal stress (zz) is 4,000 psi. Find: the major, intermediate, and minor...

The rate of formaldehyde (CH2O) oxidation over a Ag=SiO2 catalyst at 493 K and a CH2O pressure of 9 Torr in air was 1:4 x 10 7 mole CH2Os 1 cm 3. The catalyst particles passed through a 100-mesh...

With reference to Problem 1.15, find the magnitude of the maximum shear stress and show by sketch the orientation of the plane it acts on.

FreeBSD, Mac OS , etc. ) among the AUBG students, the professor in Statistica conducted a survey with his 9 5 students. Assume that they represent a random sample.From the sample of 9 5 students, 2 8...

Pt 4 6. A researcher is studying the SAT 1 Math scores of two groups of students: those who plan to apply for financial aid and those that do not. Two independent random samples yield the following:...

What is the output of this Java program? class Driver { public static void main ( String [ ] args ) { int a = 2 6 ; int b = 0 ; for ( int c = 5 ; c 3 ; c - - ) { b = 5 ; while b = b - 1 ; a = a + b ;...