Question: A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile load of 27,500 N. It

A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile load of 27,500 N. It must not experience either plastic deformation or a diameter reduction of more than 7.5 ? 10^-3 mm. Of the materials listed as follows, which are possible candidates? Justify your choice(s).

Modulus of Elasticity Yield Strength Poisson's Ratio Material (GPa) 70 (MPa) 200

Modulus of Elasticity Yield Strength Poisson's Ratio Material (GPa) 70 (MPa) 200 Aluminum alloy 0.33 Brass alloy 101 0.34 300 Steel alloy 400 207 0.30 Titanium alloy 107 650 0.34

Step by Step Solution

★★★★★

3.37 Rating (169 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

This problem asks that we assess the four alloys relative to the two criteria pr... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

33-E-M-S-E-M-S (185).docx

120 KBs Word File

Students Have Also Explored These Related Materials Science Engineering Questions!

A cylindrical rod 120 mm long and having a diameter of 15.0 mm is to be deformed using a tensile load of 35,000 N. It must not experience either plastic deformation or a diameter reduction of more...

A long horizontal cylinder having a diameter of 10 cm is maintained at a temperature of 100C and centered in a 30-cm-thick slab of material for which k = W/m C. The outside of the slab is at 20C....

A pipe having a diameter of 10 cm passes through the center of a concrete slab having a thickness of 70 cm. The surface temperature of the pipe is maintained at 100C by condensing steam while the...

A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile load of 27,500 N. It must not experience either plastic deformation or a diameter reduction of more...

6 . 2 3 A cylindrical rod 1 0 0 mm long and having a diameter of 1 0 . 0 mm is to be deformed using a tensile load of 2 7 , 5 0 0 N . It must not experience either plastic deformation or a diameter...

a) = Consider a Co-Cr alloy used for vascular stent application. The alloy has a fracture toughness of K;c = 60 MPaym, a yield strength of Quieid=547 MPa an ultimate tensile strength of 1449 MPa, a...

3. (25pts) A cylindrical rod 120 mm long and having a diameter of 15.0 mm is to be deformed using a tensile load of 50,000 N. It must not experience either plastic deformation or a diameter reduction...

A cylindrical rod 380 mm long, having a diameter of 10.0 mm, is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.9 mm, when...

8. Designing an efficient and robust windmill is important for converting wind energy to electricity. Suppose a windmill fan is supported by a cylindrical rod 350 mm long, having a diameter of 13.5...

Table 1 shows a list of materials and their mechanical properties. Each of the material will undergoes tensile test as a cylindrical rod specimen with 380 mm long and having a diameter of 10 mm. If...

For portfolio P with investment proportions of .60 in A and .40 in B, rework Problems 9, 10, and 12. Suppose that the index model for stocks A and B is estimated from excess returns with the...

1. Show full solutions for the following questions related to the rolling of two standard dice. a. What is the probability a rolling a sum of 7 OR Doubles? b. What is the probability of rolling a sum...

company has a certain marginal tax rate they plan to make an investment a certain amount of cash flow and income instead of making ght reinvestment directly

Prove that the equation ax ay (mod n) implies x y (mod n) whenever gcd (a, n) = 1. Show that the condition gcd (a, n) = 1 is necessary by supplying a counterexample with gcd (a, n) > 1.

For the network shown in fig 13.5 find io(t),t>0.

A factory employs 3000 unionized workers, 90% of whom are male. A random sample of 15 workers is selected for a survey about worker satisfaction. Let p = the proportion of males in the sample. a....

A modern jet engine has a temperature after combustion of about 1500 K at 3200 kPa as it enters the turbine section (see state 3, Fig. P4.124). The compressor inlet is at 80 kPa, 260 K (state 1) and...

Of 1019 U.S. adults responding to a 2017 Harris poll, 47% said they always or often read nutrition labels when grocery shopping. a. Construct a 95% confidence interval for the population proportion...

Let the voltage output of the battery and resistances in the parallel connection in Figure 21.4 be the same as the previously considered series connection: V = 12.0 V, R1 = 1.00 , R 2 = 6.00 , and R...

Molecular weight data for some polymer are tabulated here. Compute (a) the number-average molecular weight, and (b) the weight-average molecular weight. (c) If it is known that this material's degree...

Is it possible to have a poly(methyl methacrylate) homopolymer with the following molecular weight data and a of polymerization of 527? Why or why not? Molecular Weight Range (g/mol 19 8,000-20,000...

High-density polyethylene may be chlorinated by inducing the random substitution of chlorine atoms for hydrogen. (a) Determine the concentration of Cl (in wt%) that must be added if this substitution...

The new equipment will have a cost of $1,800,000, and it will be depreciated on a straight-line basis over a period of six years (years 1-6). The old machine is also being depreciated on a...

The Beasley Corporation has been experiencing declining earnings but has just announced a 50 percent salary increase for its top executives. A dissident group of stockholders wants to oust the...

You are given that 1) Event A = going to school 2) Event B = going to sleep 3)P(A) = 0.20, 4) P(B) = 0.30 5) P(A and B) = 0.12. Explain using math why the events may or may not be independent.