Question: Calculate the ultimate tensile strength (engineering) of a material whose strength coefficient is 400 MPa and of a tensile-test specimen that necks at a true

Calculate the ultimate tensile strength (engineering) of a material whose strength coefficient is 400 MPa and of a tensile-test specimen that necks at a true strain of 0.20.

Step by Step Solution

★★★★★

3.30 Rating (165 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The relationship between true stresstrue strain is approximately given by the el usher K Where is th... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

972-E-M-E-B-D (253).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

Based on the information given in Fig. 2.6, calculate the ultimate tensile strength of annealed 70-30 brass.

A 20 full-depth steel spur pinion rotates at 1145 rev/min. It has a module of 6 mm, a face width of 75 mm, and 16 milled teeth. The ultimate tensile strength at the involute is 900 MPa exhibiting a...

Determinations of the ultimate tensile strength Sut of stainless steel sheet (17-7PH, condition TH 1050), in sizes from 0.016 to 0.062 in, in 197 tests combined into seven classes were Where f is the...

1. The graph shows the flow stress (plastic true stress-strain curve) of an annealed copper alloy which was measured in uniaxial compression. The strain-hardening coefficient is n = 0.45 and the...

Given: The ultimate tensile strength, S u t , of a material can be calculated from its strength coefficient, K , and strain hardening exponent, n . Assume that a material has a true stress - true...

solve these problems with step by step explanation The article from which the data in Exercise 1 was extracted also gave the accompanying strength observations for cylinders: 6.1 5.8 7.8 7.1 7.2 9.2...

The findings of a tensile test on a mild steel specimen were as follows: Diameter of the test piece 12.5 mm, Gauge length 40.0 mm, Load at yield point 28.8 KN Maximum load 68.5 kN, Distance between...

12mm $2 (a) A single crystalline dog bone shape NiCoCr alloy exposed to 700 N uniaxial force along the [001] direction. The width of cross section is 3 mm with 1 mm thickness. Please find out if this...

can you help me please, could you solve my questions which are select them in red circle ,i believe that they are easy for you and you will help me because it is my last question right :( Sort the...

please help me on question which i draw them in red circle if you help me i will help you 2 Which one of the below given occasions can not be counted among the reasons of risen interest on...

APC is a contract manufacturer of printed circuit board assemblies that specializes in manufacturing and test engineering support of complex printed circuit boards for companies in the defense and...

Russia is the worlds 3rd oil producer, the 2nd natural gas producer and among the top 5 producers of steel, nickel and aluminum. It is also the largest wheat exporter in the world (almost 20% of...

31. The following transactions took place at the Townsend Employment Agency during October 20X1. Record the general journal entries that would be made for these transactions. Use a compound entry for...

In what ways did British experience in the early 1980s illustrate the problems with monetary targeting?

Repeat Prob. 3100 with an OD of 2 in and wall thickness of 0.25 in. Repeat Prob. 3100, An AISI 1040 cold-drawn steel tube has an OD = 50 mm and wall thickness 6 mm. What maximum external pressure can...

Repeat Prob. 3100 with an internal pressure. Repeat Prob. 3100, An AISI 1040 cold-drawn steel tube has an OD = 50 mm and wall thickness 6 mm. What maximum external pressure can this tube withstand if...

Repeat Prob. 3101 with an internal pressure. Repeat Prob. 3101, An AISI 1040 cold-drawn steel tube has an OD = 50 mm and wall thickness 6 mm. What maximum external pressure can this tube withstand if...

When Cameron and Ashley allow a customer to buy on credit, which account increases? a. debt b. inventory c. accounts payable d. accounts receivable

Can someone help me with this? With the steps to follow in the exercises please present the processes necessary to support the answers to the exercises and round the final results ? not the...

PROBABILITY EXPERTS ANSWER WELL AND PROMPTLY Which of the accompanying Control Panel applets can be utilized to change the name of a PC or add the PC to an area? By recognizing mindful as individual...