Question: A cutting tool uses a nozzle that generates a high speed jet of liquid water. Assume an exit velocity of 1000 m/s of 20oC liquid

A cutting tool uses a nozzle that generates a high speed jet of liquid water. Assume an exit velocity of 1000 m/s of 20oC liquid water with a jet diameter of 2 mm (0.002 m). How much mass flow rate is this? What size (power) pump is needed to generate this from a steady supply of 20oC liquid water at 200 kPa?

Step by Step Solution

★★★★★

3.33 Rating (165 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

CV Nozzle Steady state single flow Continuity equation with a ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

E-ME-T (671).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

liquid flows in a round pipeline. The mass flow rate is 9800 kg/s. The Reynolds number is 6 million. Kinematic viscosity is 1.4E -6 m 2 /s and S G = 0.9. Calculate the pipe diameter in meters. Choose...

A pump takes 10C liquid water in from a river at 95 kPa and pumps it up to an irrigation canal 20 m higher than the river surface. All pipes have diameter of 0.1 m and the flow rate is 15...

Liquid water at 200 kPa and 15C is heated in a chamber by mixing it with superheated steam at 200 kPa and 150C. Liquid water enters the mixing chamber at a rate of 4.3 kg/s, and the chamber is...

A relatively small diameter, high pressure water jet can cut small pieces of steel. The device shown here is a very, very (absurdly) big jet, for cutting steel bridges. At the top of the water jet...

12B please circle the answers please circle the answers please circle the answers please circle the answers please circle the answers please circle the answers please circle the answers please circle...

1. Water at 93.3C is being pumped from a large storage tank at 1atm abs at a rate of 0.189m3/min by a pump. The motor that drives the pump supplies energy to the pump at a rate of 1.49kW. The water...

ATTEMPT ALL QUESTIONS. BE SURE TO ANSWER A body with mass m = 1 2 kg is attached to the end of a spring that is stretched 2 m by a force of 100 N. Furthermore, there is also attached a dashpot4 that...

5-180 Determine the power input for a compressor that compresses helium from 150 kPa and 20C to 400 kPa and 200C. Helium enters this compressor through a 0.1-m2 pipe at a velocity of 15 m/s. 5-181...

University of Hartford Department of Civil, Environmental and Biomedical Engineering CE 320 Water Resources Engineering Spring Semester 2017 Lab #5 - Pump Performance Characteristics Report Outline...

The city of Streetville is considering adding bike lanes to some of its most popular roads in hopes to offer an alternative travel mode for local residents. The city wants to survey Streetsville...

Locate the distance y to the centroid of the member?s cross-sectional area. 0.5 in. 0.5 in. 6 in. 1.5 in. 1 in. -3 in. -3 in.-

Based on each positions power base(s), what outcomes would a person in this position be likely to experience if they were acting as a leader?

C= ? M= $850,000.00 $425,000.00 i= 6% 0.06 0.005 MENSUALMENTE n= 18 meses formula: M= C(1+i) C= M/(1+i) $388,507.87 DETERMINADO POR FORMULA C= $425,000.00 (1+0.005)^18 1.005 C= $425,000.00 1.09392894...

Why might sensitivity analysis be a useful technique in a linear programming problem?

If a projects IRR exceeds its _____, the project should be _____. cost of capital; rejected MIRR; rejected NPV; accepted cost of capital; accepted

Which one of these statements correctly applies to a limited partnership? Multiple Choice All partners share the daily management duties. O All partners enjoy limited personal liability General...

Blossom Railroad C0. is about to issue $145,000 of 8 -year bonds that pay a 6.0% annual interest rate, with interest payable semiannually. The market interest rate is 5%. How much can Blossom expect...