Question: Determine the normal force, shear force, and moment at a section passing through point C. Assume the support at A can be approximated by a

Determine the normal force, shear force, and moment at a section passing through point C. Assume the support at A can be approximated by a pin and B as a roller.

Units used:

kip = 103 lb

Given:

F1 = 10 kip a = 6 ft

F2 = 8 kip b = 12 ft

w = 0.8kip/ftc = 12 ft

d = 6 ft

F2 F1 в

F2 F1

Step by Step Solution

★★★★★

3.51 Rating (164 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

0 wb c By b c Fb c d Bb c F a 0 W b c 2 F 0 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

32-E-C-S (629).docx

120 KBs Word File

Students Have Also Explored These Related Civil Engineering Questions!

Determine the normal force shear force and moment at a section passing through point D of the two memberframe. 400 N/m 200 N/m 2.5 m 6m-

Determine the normal force shear force and moment at sections passing through points E and F. member BC is pinned at B and there is a smooth slot in it at C. The pin a C is fixed to memberCD. 500 Ib...

Determine the normal force. Shear force and moment at a section passing through pointC. Assume the support at A can be approximated by a pin and B as aroller 8 kip 10 kip 0.8 kip'ft -6 ft- -12fA- -12...

Determine the normal force, shear force, and moment at a section passing through point D of the two-memberframe. 400 N/m 25 m

Determine the normal force, shear force, and moment at a section passing through point D of the two-member frame. Units Used: kN = 103 N Given: w1 = 200N/m w2 = 400N/m a = 2.5 m b = 3 m c = 6 m W2...

Determine the normal force, shear force, and moment at a section passing through point C. Assume the support at A can be approximated by a pin and B as a roller. Units used: kip = 103 lb Given: F1 =...

7-11. 2500 lb 3000 lb 75 1b/ft The shaft is supported by a journal bearing at A and a thrust bearing at B. Determine the normal force, shear force, and moment at a section passing through (a) point...

The shaft is supported by a journal bearing at A and a thrust bearing at B. Determine the normal force, shear force, and moment at a section passing through (a) Point C, which is just to the right of...

Determine the normal force, shear force, and moment at a section passing through point C . Take P = 8 kN .

Determine the normal force, shear force, and moment at a section passing through point C. Take P = 8kN. 0.5 m -0.75 m- -0.75 m -0.75 m

Air flows with negligible friction through a 4-indiameter duct at a rate of = lbm/s. The temperature and pressure at the inlet are T1 = 800 R and P1 = 30 psia, and the Mach number at the exit is Ma2...

Damian's & Co was officially delisted from the ASX in mid-2017, after it was bought by an overseas private equity firm. What could be the possible reasons behind Damians decision to exit the stock...

Mr . Claus runs a successful toy making factory in the North Pole. One of his top selling items is bicycles. He currently makes and assembles every bike part in his factory, but he is considering...

Suppose a stock had an initial price of $72 per share, paid a dividend of $1.65 per share during the year, and had an ending share price of $85. Compute the percentage total return. What was the...

Patter Inc. acquired an 80% interest in Swing Company for $480,000 on January 1, 2011, when Swing had the following stockholders equity: Common stock ($10par) ............... $100,000 Additional...

Mott Company recently implemented a JIT manufacturing system. After one year of operation, Heidi Burrows, president of the company, wanted to compare product cost under the JIT system with product...

Nico Parts, Inc., produces electronic products with short life cycles (of less than two years). Development has to be rapid, and the profitability of the products is tied strongly to the ability to...

Cortalo, Inc., manufactures riding lawn mowers. Cortalo uses JIT manufacturing and carries in signiï¬cant levels of inventory. Cortalo manufactures everything needed for the riding lawn...

Do economists have any particular expertise at making normative arguments? In other words, they have expertise at making positive statements (i.e., what will happen) about some economic policy, for...

Determine (approximately) the support actions at A,B, and C of the frame. 400 lb/ft 1200 lb/ft B 15 ft 20 ft

Determine (approximately) the internal moments at joints I and L. Also, what is the internal moment at joint H caused by member HG? 0.5 k/ft K 1.5 k/ft 1.5 k/ft F D. Taont - 20 ft- 40 ft 30 ft

Sample Input/output: (The average is supposed to be actually 74.33, so why did we get 742 How to fix it to get an accurate average resulta) 81 Enter three grades: 69 7 3 The grades that you entered...

The president of the retailer Prime Products has just approached the company's bank with a request for a $30,000, 90-day loan. The purpose of the loan is to assist the company in acquiring...

score: U of 1 pt 12 of 16 (15 complete) HW Score: 93.75%, 15 of 16 pts 5.3.32-T Question Help In a recent study on world happiness, participants were asked to evaluate their current lives on a scale...