Question: Determine the total exergy destruction associated with the Otto cycle described in Problem 9-33, assuming a source temperature of 2000 K and a sink temperature

Determine the total exergy destruction associated with the Otto cycle described in Problem 9-33, assuming a source temperature of 2000 K and a sink temperature of 300 K. Also, determine the energy at the end of the power stroke.
Problem 9-33
An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 95 kPa and 27°C, and 750 kJ/kg of heat is transferred to air during the constant-volume heat-addition process.

Step by Step Solution

★★★★★

3.43 Rating (169 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The total exergy destruction associated with the Otto cycle describe... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

837-ME-T (5622).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

Determine the total exergy destruction associated with the Diesel cycle described in Problem 9-46, assuming a source temperature of 2000 K and a sink temperature of 300 K. Also, determine the energy...

Determine the total exergy destruction associated with the Brayton cycle described in Prob. 9-107, assuming a source temperature of 1500 K and a sink temperature of 290 K. Also, determine the energy...

Determine the total energy destruction associated with the Otto cycle described in Problem 934, assuming a source temperature of 2000 K and a sink temperature of 300 K. Also, determine the energy at...

Determine the total energy destruction associated with the Diesel cycle described in Problem 947, assuming a source temperature of 2000 K and a sink temperature of 300 K. Also, determine the energy...

Determine the total energy destruction associated with the Brayton cycle described in Problem 993, assuming a source temperature of 1800 K and a sink temperature of 300 K. Also, determine the energy...

6 - An air - standard Diesel cycle has a compression ratio of 1 6 and a cutoff ratio of 2 . At the beginning of the compression process, air is at 9 5 kPa and \ ( 2 7 ^ { \ circ } \ mathrm { C } \ )...

please do not handwrite , use keyboard instead. Thanks alot friend. 1. Consider an ideal steam regenerative Rankine cycle with two feedwater heaters, one closed and one open. Steam enters the turbine...

Determine the exergy destruction associated with each of the processes of the Brayton cycle described in Prob. 9-109, assuming a source temperature of 1260 K and a sink temperature of 300 K. Also,...

Determine the exergy destruction associated with the heat rejection process of the Diesel cycle described in Prob. 9-52E, assuming a source temperature of 3200 R and a sink temperature of 540 R....

Determine the exergy destruction associated with each of the processes of the Rankine cycle described inProb. 10-12, assuming a source temperature of 1500 K and a sink temperature of 290 K.

Design the LC ladder network terminated with a 1- resistor that has the normalized transfer function (This transfer function is for a Butterworth lowpass filter.) H(s) =+252+2s +1 1.

4. Write and balance the following chemical equations. (a) Nitrogen plus hydrogen produce ammonia. (b) Sodium oxide combines with water to form sodium hydroxide. (c) Zinc reacts with iron (III)...

5 How is the mouth of a crocodile adapted for feeding?

Which of the following terms is not correctly matched with its definition? a. Principal: the amount borrowed. b. Terms of the loan: cost of the item if it is not being financed. c. Down payment: the...

Determine the Z parameters for the two port network shown.

Find the Z parameters for the two port shown. Determine the voltage gain of the entire circuit with a 4k-ohm load attached.

Find the Z parameters for the two port network shown.

A cylinder and piston assembly (defined as the system) is warmed by an external flame. The contents of the cylinder expand, doing work on the surroundings by pushing the piston outward against the...

Please see the question in the attached picture. 1. Assume X1, . . . ,Xn are i.i.d. N(p.,02) where both it and 02 are unknown. Find the marginal posterior for pt, assuming the prior pm, Org) =...

We are evaluating a project that costs $1,350,000, has a six-year life, and has no salvage value. Assume that depreciation is straight-line to zero over the life of the project. Sales are projected...