Explain why the use of a given fixture may not be economical when used with one machine

Question:

Explain why the use of a given fixture may not be economical when used with one machine tool but may be economical when used in conjunction with another machine tool.

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Materials and process in manufacturing

ISBN: 978-0471656531

9th edition

Authors: E. Paul DeGarmo, J T. Black, Ronald A. Kohser

See More Books

Question Posted: May 24, 2016 06:25 AM

See More Questions

Consider a discrete memory less source whose alphabet consists of K equiprobable symbols. (a) Explain why the use of a fixed-length code for the representation of such a source is about as efficient...
Explain why two parallel wires carrying currents in opposite directions repel each other.
The use of a lens in a certain situation is described by the Equation Determine(a) The object distance and (b) The image distance. (c) Use a ray diagram to obtain a description of the image. (d)...
We have all experienced workplace or personal changes that required us to adjust our daily actions at work or at home. Select one of the changes below, and explain how you have adapted to that change...
The following control procedures are used in Morgan's Boutique Shoppe for cash disbursements. 1. The company accountant prepares the bank reconciliation and reports any discrepancies to the owner. 2....
In January 2016, Iris Corporation purchased and placed in service a 1933 building that houses retail businesses. The cost was $300,000, of which $25,000 applied to the land. In modernizing the...
Compare the field work in social media research to traditional field work.
Assume the following: the sales price to consumers is $150 the retailers markup is 50% Whirlpools after tax profit margin is 4% The hurdle rate is 20% Populations are as follows: Brazil 182...
Identify a retailer that effectively uses store design as a source of competitive advantage. Describe how the store design... Helps the retailer to stand out / capture attention Reinforces the...
1. How will you characterize Tupperwares distribution strategy in relation to the theoretical models? 2. What are the advantages and disadvantages of Tupperwares distribution model? 3. How do you...
What do we do to workholding devices to make them more flexible?
What are roll-over jigs, and what advantages do they offer?
(a) During surgery, a current as small as 20.0 A applied directly to the heart may cause ventricular fibrillation. If the resistance of the exposed heart is 300 , what is the smallest voltage that...
While scuba diving, you have injured yourself and must signal the boat on the surface for help. You have five laser pointers, each emitting light of a different color: red, orange, yellow, green, and...
The price of corn is written in which form? a . $$2$ b . $$2/bushel$ c . 2 bushels d . 2 bushels/$$$
A storage heater captures heat over a period of time, and then releases it, usually to an air stream, when required. Those for domestic heating store solar energy or energy from cheap off-peak...
Express the conservation of momentum in open form in Cartesian coordinates.
A system is described as follows: where What restrictions should be imposed on 1 , 2 , 1 1 , 2 , 1 and 2 2 so that the system is completely controllable and observable. x y = Ax + Bu = Cx
Access the 2017 consolidated financial statements of Brookfield Asset Management Inc. (BAM) at https://bam.brookfield.com/en/reports-and-filings and answer the questions below for 2017. When...
A bar of a steel alloy that exhibits the stress-strain behavior shown in Figure 6.22 is subjected to a tensile load; the specimen is 375 mm (14.8 in.) long and has a square cross section 5.5 mm (0.22...
What is roughly the relative magnitude of the work in the process 1-2c versus the process 1-2a shown in figure 4.8?
A hydraulic cylinder of area 0.01 m2 must push a 1000 kg arm and shovel 0.5 m straight up. What pressure is needed and how much work is done?
A work of 2.5 kJ must be delivered on a rod from a pneumatic piston/cylinder where the air pressure is limited to 500 kPa. What diameter cylinder should I have to restrict the rod motion to maximum...
A rhino is charging at you, so decide to sedate it with a tranquilizer gun angled at 40 as shown above. The tranquilizer gun can reach a horizontal distance of 49 m when angled at 45. (Assume ideal...
What is the definition of motivation and how can the chef foster an environment of motivation in the kitchen? What methods can a chef implement to motivate the kitchen team? What factors contribute...
Article Review Read the article. Link is given below: https://www.projecttimes.com/articles/avoid-the-top-three-real-causes-of-scope-creep.html Post your thoughts on this article, add references if...

Explain why the use of a given fixture may not be economical when used with one machine

Question:

Step by Step Answer:

If a machine is costly and has a high production rate time lost i...View the full answer

Materials and process in manufacturing

Students also viewed these Materials Science Engineering questions