Fixture ABCD is used to apply forces to photo elastic models of mechanical components For the model and forces shown, determine when alpha 50 deg (a) The resultant of the applied forces, (b) The point where the line of action of the resultant intersects a line drawn through points F and G 200 m 250 mm 150 m 60N 160 320 mm

Question: Fixture ABCD is used to apply forces to photo elastic models of mechanical components. For the model and forces shown, determine when α = 50°

Fixture ABCD is used to apply forces to photo elastic models of mechanical components. For the model and forces shown, determine when α = 50°
(a) The resultant of the applied forces,
(b) The point where the line of action of the resultant intersects a line drawn through points F and G.

200 m 250 mm 150 m 60N 160 320 mm

200 m 250 mm 150 m 60N 160 320 mm

Step by Step Solution

★★★★★

3.43 Rating (175 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

a EF b R 80 Ni 40 Nj 60 Nj 90 N sin 50i cos 50j 11056... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

4-E-M-E-VM (245).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

The airstroke actuator at D is used to apply a force of F = 200 N on the member at B. Determine the horizontal and vertical components of reaction at the pin A and the force of the smooth shaft at C...

The airstroke actuator at D is used to apply a force of F on the member at B. The normal reaction of the smooth shaft at C on the member is 300 N. Determine the magnitude of F and the horizontal and...

The parallel-link mechanism ABCD is used to transport a component I between manufacturing processes at stations E, F, and G by picking it up at a station when ( = 0 and depositing it at the next...

im have to make research paper about that so I need to summarize of this 5 page. please help me IJPPM 58,3 268 11 Plate 3. Failed heat-treat fixture Control phase The results of the new fixture were...

help 1- In designing a fixture, clamps should be located a-over a locator if possible b-on the bottom of the part c-as close together as possible d-on the thinnest sections of the part 2- Which type...

Can I have all questions answered, please? You just started a summer internship with the successful management consulting firm of Kirk, Spock, and McCoy. Your first day on the job was a busy one, as...

Question 37 Which of the following does the cost variance model use to analyze differences between actual and budgeted profits? Flexible production budget. Fixed production budget. Prior periods...

An engine repair shop has a balanced 5-station flow line to repair the engines. First, the engines are mounted on a fixture and move down the line one station at a time. Upon completion, the engines...

QUESTION 2 [25 MARKS] 2223I/BTM3514 [CO2, PO3, SK5] (a) What are the criteria for the implementation of an automated production line (APL)? [4 Marks] (b) APL are examples of fixed automation. In your...

Question 16 The hardness of steel depends upon the O amount of cementite it contains O contents of alloying elements O amount of carbon it contains method of manufacture of steel

Die A has 4 red and 2 white faces, whereas die B has 2 red and 4 white faces. A fair coin is flipped once. If it lands on heads, the game continues with die A; if it lands on tails, then die B is to...

Fred Saros is auditing cash payments for OGA, a large supermarket. OGA deals with several very large corporate suppliers who expect payment by electronic funds transfer within three business days of...

Bautista Corporation reported pretax book income of $ 1 , 4 2 5 , 0 0 0 . Included in the computation were favorable temporary differences of $ 2 3 2 , 5 0 0 , unfavorable temporary differences of $...

Extend the previous project by providing a graphical animation of the skip-list operations. Visualize how entries move up the skip list during insertions and are linked out of the skip list during...

Use MATLAB to find the angles corresponding to the following coordinates. Hand-check the answers. a. (x, y) = (5, 8) b. (x, y) = (-5, 8) c. (x, y) = (5, -8) d. (x, y) = (-5, -8)

When the speed of the electrons that strike a metal surface is increased, the result is an increase in a. the number of x-rays emitted b. the frequency of the x-rays emitted c. the speed of the...

Draw a UML diagram showing the relationships among the classes involved in the Product Sales example from this chapter.

A uniform torus and a cylindrical ring, each solid and of mass m, are released from rest in the positions shown. Determine the magnitude of the pin reaction at O and the angular acceleration of each...

24. Domestic Airfare. The Global Business Travel Association reported the domestic airfare for business travel for the current year and the previous year. Below is a sample of 12 flights with their...

In Problem 8.69, determine the couple that must be applied to shaft AB in order to rotate the large gear clockwise. PROBLEM 8.69 The square-threaded worm gear shown has a mean radius of 2 in. and a...

The vise shown consists of two members connected by two double-threaded screws with a mean radius of 0.25 in. and pitch of 0.08 in. The lower member is threaded at A and B (s = 0.35), but the upper...

The ends of two fixed rods A and B are each made in the form of a single-threaded screw of mean radius 6 mm and pitch 2 mm. Rod A has a right-handed thread and rod B has a left-handed thread. The...

Assuming that in Problem 8.75 a right-handed thread is used on both rods A and B, determine the magnitude of the couple that must be applied to the sleeve in order to rotate it. PROBLEM 8.75 The ends...

A lever of negligible weight is loosely fitted onto a 75-mmdiameter fixed shaft. It is observed that the lever will just start rotating if a 3-kg mass is added at C. Determine the coefficient of...

A single client, 64, a recently retired engineer, lives in a high income tax state. Their only income is Social Security of $31,800 per year. Living expenses are $59,000 with a mortgage payment of...