Question: Gear 2, in the figure, has 16 teeth, a 20 transverse angle, a 15 helix angle, and a module of 4 mm. Gear 2 drives

Gear 2, in the figure, has 16 teeth, a 20â—¦ transverse angle, a 15â—¦ helix angle, and a module of 4 mm. Gear 2 drives the idler on shaft b, which has 36 teeth. The driven gear on shaft c has 28 teeth. If the driver rotates at 1600 rev/min and transmits 6 kW, find the radial and thrust load on eachshaft.

LH 90 RH RH

Step by Step Solution

★★★★★

3.38 Rating (154 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Since the transverse pressur... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

233-M-E-S-G (83).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

A cast-steel C frame as shown in the figure has a rectangular cross section of 1.25 in by 2 in, with a 0.5-in-radius semicircular notch on both sides that forms midflank fluting as shown. Estimate A,...

The brake shown in the figure has a coefficient of friction of 0.30, a face width of 2 in, and a limiting shoe lining pressure of 150 psi. Find the limiting actuating force F and the torque capacity.

The extension spring shown in the figure has full-twisted loop ends. The material is AISI 1065 OQ&T wire. The spring has 84 coils and is close-wound with a preload of 16 lbf. (a) Find the closed...

Following are the activities of a Project, please consider them for answering the questions below: Activity Predecessor(s) Duration (days) A 3 B A 5 D B 7 , D C, D , F E 9. 5 G 2 H 4. I G 6. J H, I 3...

2 : In the following figure helical gear 2 on shaft a has 1 6 teeth, 2 0 transverse angle, 1 5 helix angle and a module of 4 mm . This gear drives an idler on shaft b , which has 3 6 teeth. The...

Case Write-Up #1: Marketing Chateau Margaux Please be concise in your case write-up: find the problem, assess why it happened, and propose a solution. Use the following questions as a guideline for...

A pair of full depth helical gears have a normal pressure angle of 2 0 , helix angle 2 5 and a face width of 4 5 mm . Gears steel ground teeth pinion has BHN = 3 5 0 , Sut = 8 0 0 , gear BHN = 3 0 0...

Question 1 : A 1 6 - tooth pinion drives the double - reduction - gear train. The pinion rotates at 1 2 0 0 r e v m i n and transmits power of 5 hp to the gear train. All shafts have the same...

ca 011/ An epicyclic gear train shown in figure, the arm is keyed to the same shaft as the bad drum and the wheel A is keyed to the second shaft which carries a chain wheel, the chain being operated...

( 2 0 marks ) where power transmission is bmit power between perpendicular shafts while worm gearing is employed can be integrated together for complex powallel, non - intersecting shafts. Two or...

Tandor, Inc. (a U.S. firm) borrows U.S. funds at an interest rate of 9% per year. Its beta is 1.3. The long-term annualized risk-free rate in the U.S. is 2%. The stock market return in the U.S. is...

Differentiate between an operating budget and a financial budget.

How does cost-push inflation differ from demand-pull inflation? Illustrate with two graphs.

Discuss in detail the different stages in the CSR process.

For the shaft shown in the figure, let a1 = 4 in, b1 = 12 in, a2 = 10 in, F1 = 100 lbf, F2 = 300 lbf, and E = 30 Mpsi. The shaft is to be sized so that the maximum slope at either bearing A or...

If the diameter of the beam for Prob. 426 is 1.375 in, determine the deflection of the beam at x = 8 in.

See Prob. 426 and the accompanying figure. The loads and dimensions are F1 = 3.5 kN, F2 = 2.7 kN, a1 = 100 mm, b1 = 150 mm, and a2 = 175 mm. Find the uniform shaft diameter necessary to limit the...

t answers by question parts. The number of submissions remaining for each question part only changes if you submit or change the answer. Assignment Scoring Your last submission is used for your...

twenty nine different video games showingviolence were observed. The duration times of violence (in seconds) were recorded. When using this sample for a t test of the claim that the population mean...

El trabajo 521 fue uno de los muchos trabajos iniciados y completados durante el ao. El trabajo requiri $5,400 en materiales directos y 700 horas de mano de obra directa a razn de $14 por hora. Si el...