Question: It has been stated that dimensional tolerances for nonmetallic stock, such as plastics, are usually wider than for metals. Explain why. Consider physical and mechanical

It has been stated that dimensional tolerances for nonmetallic stock, such as plastics, are usually wider than for metals. Explain why. Consider physical and mechanical properties of the materials involved.

Step by Step Solution

★★★★★

3.34 Rating (166 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Dimensional tolerances for a nonmetallic stock are wider than for metals because the ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

972-E-M-E-B-D (356).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

It has been stated that the vibrating earth has a resonance period of 54 min and a Q factor of about 400 and that after a large earthquake, the earth rings (continues to vibrate) for about 2 months....

It has been stated that the higher the value of m, the more diffuse the neck is, and likewise, the lower the value of m, the more localized the neck is. Explain the reason for this behavior.

It has been stated that as the normal load decreases, abrasive wear is reduced. Explain why this is so.

Lecture Notes DL MGT 5100 - Distribution Management Spring 2017 1.0. Day one, Monday, Monday, 9 Jan 17 1.1. Reading Assignments: Chapters 1 and 2 1.1.1. I intend to follow the book so as to provide a...

Building and Construction BSBSMB401 Establish legal and risk management requirements of small business Learner Materials and Assessment Tasks Table of Contents About BSBSMB401 Establish legal and...

Do you expect robots to have a bigger impact inside or outside of factories in the next 15 years, and what implications does your answer have for the kinds of strategies that will gain competitive...

SUMMARY this article for about 2 pages with single spacing. Thank you. ECONOMETRICS: MEASUREMENT I N ECONOMICS1 I As the first incumbent of a new Chair in this University, I thought that in this...

Based on the following Case study on LEGO Answer the following 4 questions. 1. What are LEGO's values and corporate identity? (/3) How did these develop over time (prior to LEGO Media Int'l)? 2. How...

How would you define quality and how is quality measured in the airline industry? Are some measurements more useful than others? Explain.

Menezes Chemical Company produces a chemical cleaning solvent in three departments, Refining, Blending, and Finishing. The process begins in the Refining Department, where the base solvent is removed...

14.7 The extraction rate of a certain polymer is known to depend on the reaction temperature and the amount of catalyst used. An experiment was conducted at four levels of temperature and five levels...

What is being assumed about the timing of wage setting and price setting that enables us to say that the economy is always on the PS curve but only on the WS curve in a medium-run equilibrium? What...

When a motor armature inertia, a pinion inertia, and a motor torque reside on a motor shaft, and a gear inertia, a load inertia, and a load torque exist on a second shaft, it is useful to reflect all...

Apply the rules of Prob. 1626 to the three-shaft system shown in the figure to create a motor shaft shish kebab. (a) Show that the equivalent inertia Ie is given by (b) If the overall gear reduction...

For the conditions of Prob. 1627, make a plot of the equivalent inertia Ie as ordinate and the stepdown ratio n as abscissa in the range 1 n 10. How does the minimum inertia compare to the...

A group of bankers is evaluating a failing toy business named 'The Toy Brick' that is going to shut down next year, and the bankers would like to determine if they should buy it this year. The...

A runner tracks their performance by recording race information in a journal. The journal contains the event name, the race in kilometers and the time of completion. Classify each variable as...

Directions: Assume you are a new manager in the Financial Analysis department and are orienting a team of new college graduates to the world of capital budgeting. In your initial post, explain the...