Using Taylors equation in Exercise 4, show that tool wear and cutting speed are related by T
Question:
Using Taylor’s equation in Exercise 4, show that tool wear and cutting speed are related by T2 = T1(V1/V2)1/n.
Exercise 4
VTn = C
Fantastic news! We've Found the answer you've been seeking!
Step by Step Answer:
Answer rating: 72% (11 reviews)
The Taylor model This prompted Taylor to develop a model focused on the effect of varying cutti...View the full answer
Answered By
Dudhat Vaidehi
I tutored mostly elementary school students privately after school and during the summer. We met in their homes or at the public library. I charged an hourly fee, and I provided any necessary materials.
Having taught in special education in two local schools for many years meant that I had contact with a lot of parents of special needs students. I never had to advertise — word of mouth was how most folks knew of me. At one point I did have a website, but didn't utilize it much. I stayed very busy, especially in the summers, and always had a full schedule. I typically met with each student's teacher in order to get an idea of what the focus of my instruction/remediation should be. Becoming familiar with the student's learning style(s) was also very helpful. Often parents would share records and test results with me. After each tutoring session, I documented the student’s progress and gave parents written updates, as well as phone calls or emails as needed.
While my students and I certainly utilized technology and the internet often during our sessions, I never tutored online or for any tutoring company, so am not familiar with the curriculums or methods used in those settings.
Tutoring one on one was very enjoyable and rewarding. My students and I had fun, and grew quite fond of one another. The extra income was a bonus. I had to retire from tutoring due to a physically handicapping disease, and miss my students very much.
0.00
0 Reviews
10+ Question Solved
Related Book For
Exploring Engineering An Introduction to Engineering and Design
ISBN: 978-0123747235
2nd edition
Authors: Philip Kosky, George Wise, Robert Balmer, William Keat
Question Posted:
Students also viewed these Engineering questions
-
The Taylor Tool company manufactures hardened tool steel. The specifications for one of its products products, A768C, requires a hardness of 550 + 50. The following data have been collected on steel...
-
In Figure 22-A are data for cutting speed and tool life. Determine the constants for the Taylor tool life equation for these data. What do you think the tool material might have been?
-
In the Taylor series (4.85) of Prob. 4.1, let the point x = a be called xn (that is, xn ¡ a) and let s ¡ x - a = x - xn, so x = xn + s. (a) Use this notation to write (4.85) as f(xn + s)...
-
What is the cofactor of an entry of a matrix? How are cofactors used to find the determinant of the matrix?
-
Use indefinite integrals to solve the following differential equations. Sketch a graph of the rate of change and the solution on the given domain. dp/dt = 5t3 + 5/t2 with p(1) = 12.0. Sketch the rate...
-
In what ways does the Navier-Stokes equation, a fundamental differential equation governing fluid flow, elucidate the intricate interplay between viscosity, inertia, and pressure gradients within a...
-
What are the major forms of a business? Why would there need to be any difference between them? What are some advantages and disadvantages to each form?
-
Tatum Company has four products in its inventory. Information about the December 31, 2018, inventory is as follows: Required: 1. Determine the carrying value of inventory at December 31, 2018,...
-
The following data from the just completed year are taken from the accounting records of Mason Company: Sales Direct labor cost Raw material purchases Selling expenses Administrative expenses...
-
Calculate the mass ( in metric tons ) of a blade made of Aluminum, M_{blade}^{Al}MbladeAl , setting the stress limit equal to fatigue limit of the material, \sigma_0^{Al} = 150 MPa0Al=150MPa.
-
For a particularmachining operation n = 0.6 and C = 350 mm/min 0.4 in the Taylor equation given in Exercise 4. What is the percentage increase in tool life when the cutting speed V is reduced by (a)...
-
A shaft 150. mm long with an initial diameter of 15. mm is to be turned to a diameter of 13.0 mm in a lathe. The shaft rotated at 750. RPM in the lathe and the cutting tool feed rate is 100....
-
Under what kind of range forage conditions would horses have comparative nutritional advantages over cattle?
-
Isopropanol can dehydrate to either propylene or diisopropyl ether over the temperature range: 25 - 300C and 1 bar total pressure. Analysis of the reaction system detects isopropanol, diisopropyl...
-
Solve Exiyll + sinx y + y =o X
-
a. Determine the size of the IC and VCE dc!b. Draw an ac equivalent circuit!c. Derive the Zi, Zo, and Av equations!d. Count Zi, Zo, Av and AP! H 8292 Vi 1 F HH Ic HH Vo Zo B=90 1 F + +9V 680 Si Si...
-
Solve the following Volterra Integral Equations using 1. Laplace transform 2. Variational Iterationl Method a) Volterra integral equation with weakly singular kernel u(x)=x+1+ xt-1 u(t)dt the exact...
-
Overview: This is a group assignment that allows students to apply what they learned in ECON 1001. Students will explain one or more basic global macroeconomics concepts and principles (CLO 2). They...
-
Sound of a given frequency leaves a loudspeaker and spreads out due to diffraction. The speaker is placed in a room that contains either air or helium. The speed of sound in helium is about three...
-
Determine the reactions in supports A and D and connections B and C. Sketch its shear and moment diagram and determine the magnitude ankoration of the maximum shear and moment for every member. 18 3...
-
Refer to Figure 9.1, where a 2.0 m 3.0 m flexible foundation is placed in a saturated clay at 1.5 m depth. Bedrock lies at 4.0 m below the foundation. The clay is overconsolidated with OCR = 2,...
-
For an elastic material, the bulk modulus (K) and Youngs modulus (E) are related by For undrained loading, deduce that s = 0.5. 1 K = 3(1 - 2.,)
-
A 2 m 4 m flexible foundation is placed on a granular soil with Df 5 0. The foundation applies a pressure q o = 120 kN/m 2 . Assuming the soil mass to be infinitely thick, with E s = 15 MN/m 2 and ...
-
Calendar Plc have a year end of 30/09/X2. They have prepared the following information about their non-current assets: Land was revalued to 4.2 million on 28/09/X2 All buildings are depreciated using...
-
Antique Accents reported the following on its 2020 income statement. Using the income statement and the balance sheet given below, prepare the statement of cash flows using the indirect method. For...
-
Jamal, Maggie, and Kendra are dividing an estate consisting of a house, a vacation home, and a small business. Their valuations are shown below. Determine the payment that Kendra receives from the...
Study smarter with the SolutionInn App