Question: If, in problem 16.5, the process is improved so the standard deviation is 0.0035, is the process capable now? In Problem The specification for the

If, in problem 16.5, the process is improved so the standard deviation is 0.0035, is the process capable now?

In Problem

The specification for the diameter of a hole is 0.80 inch ±0.020 inch. The standard deviation of the drill press is 0.007 inch. Using C_p, calculate whether the process is capable or not.

Step by Step Solution

★★★★★

3.31 Rating (163 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

C P USL LSL6 765 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Introduction Materials Management Questions!

The specification for the diameter of a hole is 0.80 inch 0.020 inch. The standard deviation of the drill press is 0.007 inch. Using C p , calculate whether the process is capable or not.

In problem 16.6, what is the C pk when a. The process is centered on 0.75? Is the process capable? b. The process is centered on 0.74? Is the process capable? In Problem The specification for the...

The opening backlog is 800 units. Forecast demand is as shown here. Calculate the weekly production for level production if the backlog is to be reduced to 100 units. 3 5 2 4 6. Week Total Forecast...

16.6 If, in problem 16.5, the process is improved so the standard deviation is 0.0035, is the process capable now?

If in problem 16.5 the process is improved so the standard deviation is .0035, is the process capable now? LO.1

A metal fabricator is looking at the outer diameter of connecting rods that have been produced. The rods are designed to have an outer diameter with a lower specification limit of 0 . 9 9 inch and an...

Course Project Figure (1) provides the details of a bracket assembly to hold a strut on an automobile in place. Welded to the auto body frame, the bracket cups the strut and secures it to the frame...

\ This case was developed solely for the purpose of classroom discussion. Some details of the case have been disguised. This case is not intended to serve as endorsements, sources of academic or...

Group: Amira- Meera -Noura 1- Introduction 2- Literature a. Definition of operation management b. Definition of operation strategy and why it is important c. Components of operations strategy 3- Case...

Problem 4 ABC is a company that manufactures screws for desk lamps. The design specification for the diameter of the screw is 0.8 +0.008 cm, where 0.8 is the target" diameter and 0.008 is the...

Compare the profitability , solvency, liquidity of the two companies in details using the ratio provided above (use bullet points to discuss each performance ration " profitability , solvency,...

In the network shown Vo=2 1 j1C2 1 6400A Z 2

Beginning work in process inventory Direct materials Conversion \ table [ [ 5 1 3 1 , 5 5 5 2 4 , 1 2 0 , $ 1 5 5 , 6 7 5 ] , [ , ] , [ 8 2 5 , 9 4 5 , ] , [ 2 0 7 , 2 5 s , 1 , 5 3 3 , 9 0 9 ] , [ ,...

1. What is the difference between leadership and management?

What are the two ways of balancing capacity available and load? Which is preferred? Why? LO.1

What are some of the ways capacity available can be altered in the short run? LO.1

Why is feedback necessary in a control system? LO.1

Ove r the last 10 years a firm has had the earnings per share shown in the following table: Year Earnings per share 2012 $4.00 2011 3.80 2010 3.20 2009 2.89 2008 3.20 2007 2.40 2006 1.20 2005 1.80...

A stock had returns A stock had returns of 17.09 percent (1 year ago), -23 85 percent (2 years ago), times (3 years ago), and 26.75 percent (4 years ago) in each of the past 4 years. Over the past 4...

I think I got the graph right, but the true/false question is throwing me off. Thanks! An NPV profile plots a project's NPV at various costs of capital. A project's NPV profile is shown as follows....