Question: A device which is used for pumping water in to the boiler is called (a) Economiser (b) Feed pump (c) Injector (d) Air preheater

A device which is used for pumping water in to the boiler is called

(a) Economiser

(b) Feed pump

(c) Injector

(d) Air preheater

Step by Step Solution

★★★★★

3.43 Rating (156 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Introduction Mechanical Engineering Questions!

Q:

A loan of $3,000 for a new, high-end laptop computer is to be repaid in 15 end-of-month payments (starting one month from now). The monthly payments are determined as follows. What nominal and...

Q:

Visualize, describe, and explain the strategic management process according to Ketchen and Short (2011).

Q:

Displaytotalsalesofthoseproductsbyproductlinewhichhavebeenorderedinat least4 distinct orders. output should be: tables are:orderline_t: product_t: ProductLineID TotalSales 2 6500.00

Q:

The wastewater treatment plant at the Ossabaw Paper Company paper mill generates about 24 tonnes of sludge per day. The consistency of the sludge is 35%, meaning that the sludge contains 35 wt%...

Q:

Case Study: SO2 Removal from Power Plant Stack Gases I. Introduction Numerous inventories of the world's energy reserves have shown that coal is the most abundant practical source of energy for the...

Q:

University of Hartford Department of Civil, Environmental and Biomedical Engineering CE 320 Water Resources Engineering Spring Semester 2017 Lab #5 - Pump Performance Characteristics Report Outline...

Q:

SYSTEM DESCRIPTION Throttling Valve Surrounding 30C Cooling Tower Cold Storage Evaporator Condenser Cooling Water Chilled Water Compressor Refrigerant circulation Ambient Air 30C 60% RH Drive Motor...

Q:

BIOMASS BOILER OPERATION ANALYSIS A fuel silo stores the biomass waste fuel and is fed into the boiler using a conveyor system. Combustion air is preheated before entering the boiler using an air...

Q:

5-180 Determine the power input for a compressor that compresses helium from 150 kPa and 20C to 400 kPa and 200C. Helium enters this compressor through a 0.1-m2 pipe at a velocity of 15 m/s. 5-181...

Q:

ATTEMPT ALL QUESTIONS. BE SURE TO ANSWER A body with mass m = 1 2 kg is attached to the end of a spring that is stretched 2 m by a force of 100 N. Furthermore, there is also attached a dashpot4 that...

Q:

Assignment 1 (a) - 4 Marks 1. Identify at least 10 types of hazards that are to be found in your workplace/industry. Hazard: potential source of harm .. a state or set of conditions of a system ......

Q:

Question: 1. IFRS for its external financial reporting. The amount contributed by Midland for its defined contribution plan for 2018 amounted to $55,000 and the amount contributed by Bailey for its...

Q:

The demand for diamonds is given by PZ = 980 - 2QZ where QZ is the number of diamonds demanded if the price is PZ per diamond. The total cost (TCZ) of the De Beers Company (a monopolist) is given by...

Q:

The Seller shall obtain all necessary third - party consents. How can this provision be update to include the seller's potential inability to get all consents and and to avoid liability of a breach...

Q:

Characteristics of antiwar demonstrators. Refer to the American Journal of Sociology (Jan. 2014) study of the characteristics of antiwar demonstrators in the United States, Exercise 2.106 (p. 105)....

Q:

In the mechanism \(A B C D\) shown in the given Fig.21, the fixed link is denoted as (1), Crank \(A B\) as (2), rocker \(B D\) (3), Swivel trunnion at \(C\) as (4) The instantaneous centre \(I_{4}\)...

Q:

Which one of following is an Open Pair? (a) Ball and socket joint (b) Journal bearing (c) Lead screw and nut (d) Cam and follower.

Q:

The gear train usually employed in clocks is a (a) reverted gear train (b) simple gear train (c) sun and planet gear (d) differential gear.

Q:

Assigning manufacturing overhead costs and other indirect costs is called A . materials requisition. B . cost driver. C . cost allocation. D . predetermined manufacturing overhead rate.

Q:

ent Saved Help Save & Exit Sub Required information [The following information applies to the questions displayed below.] Morganton Company makes one product and it provided the following information...

Q:

Using the information below, calculate the Return on Assets ratio. 16 Account Name Sales Revenue Sales Discounts Wage Expense Interest Expense Cost of Goods Sold Bad Debt Expense Allowance for...