Question: Fluid is a substance that: (a) Cannot be subjected to shear force (b) Always expands until it fills any container (c) Has the same shear

Fluid is a substance that:

(a) Cannot be subjected to shear force

(b) Always expands until it fills any container

(c) Has the same shear stress at a point regardless of its motion

(d) Cannot remain at rest under action of any shear force

Step by Step Solution

★★★★★

3.44 Rating (151 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Introduction Mechanical Engineering Questions!

Q:

Managing Scope Changes Case Study Scope changes on a project can occur regardless of how well the project is planned or executed. Scope changes can be the result of something that was omitted during...

Q:

A small torch bulb is placed at the focal point of a converging lens. When the the bulb is switched on, does the lens produce a convergent,divergent or parallel beam of light?

Q:

Fluid is a substance that (a) cannot be subjected to shear forces (b) always expands until it fills any container (c) has the same shear stress.at a point regardless of its motion (d) cannot remain...

Q:

The channel section shown is subjected to a vertical shear force of V = 4 kips. Calculate the horizontal shear stress \ tau _ ( A ) at point A , and the vertical shear stress \ tau _ ( B ) at point B...

Q:

computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 \ deg C to 3 0 \ deg C . Assume...

Q:

Computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 C to 3 0 C . Assume the specific...

Q:

Computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 C to 3 0 C . Assume the specific...

Q:

Choose the correct assumption from the list below regarding viscosity O a. For liquids, both the dynamic and kinematic viscosities are practically independent of pressure. O b. For gases, dynamic...

Q:

Who qualifies as an expert witness? 100 - 150 Words 13 DOCUMENTING AND PRESENTING THE CASE INTRODUCTION This chapter will explain how to pull everything together into a coherent report, and then,...

Q:

A monopolist firm has the following cost function: C(q)=0.5q^ 2 +10q+2 The (inverse) demand function for the monopolists output is as follows: P(q) = 100 - q a. Assume that the monopolist must charge...

Q:

The Montha Company was incorporated on April 1, 20X1. Montha had 10 holders of common stock. Chenda Montha, who was the president and CEO, held 51% of the shares. The company rented space in chain...

Q:

What is the maximum amount of rent that Mike can deduct this year under each type of accounting methoc? Multuple Choice $ 5 , 0 0 0 under the cash method and $ 1 5 , 0 0 0 under the accrual method $...

Q:

They were inspected again for rough grain and any knots that could cause quality problems. Any rejects were then cut into shorter usable lengths for shorter handrails or spindles? LO.1

Q:

Determine the change in internal energy when one \(\mathrm{kg}\) of steam expands from \(10 \mathrm{bar} 300^{\circ} \mathrm{C}\) to 0.5 bar and 0.9 dry. Take \(c_{p s}=2.1 \mathrm{~kJ} /...

Q:

What do you understand by the term priming ?

Q:

Entropy of wet steam is given by (a) \(s_{f}+x s_{f g}\) (b) \(x s_{g}\) (c) \(s_{g}+s_{f g}\) (d) \(x s_{f}\)

Q:

the newspaper reported last week that Tisch Enterprises earned $34.18 million this year. The report also stated that the firm's reutn on equity is 13 percent. The firm retsins 80 percent of its...

Q:

What is project scoping

Q:

Suppose an expression has connectives V ,, and variables p, r, s, t. How many rows does its truth table have?