Question: The increase in hardness due to cold working is called: (a) Cold hardening (b) Hot hardening (c) Strain hardening (d) Age hardening

The increase in hardness due to cold working is called:

(a) Cold hardening

(b) Hot hardening

(c) Strain hardening

(d) Age hardening

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Introduction Mechanical Engineering Questions!

Q:

1. Based on the information provided in the case below, what is the key strategic goal for Tim Hortons as of August 2014? It would be a year of dramatic change for Tim Hortons Inc. On August 26,...

Q:

respond to the instruction using the following criteria: Individual Written Case Exercise Respond to the specific questions provide in the case document it will be seven documents. Please make sure...

Q:

Read the case study and answer the question below with a one page response. What does a SWOT analysis reveal about the overall attractiveness of Under Armours situation? Founded in 1996 by former...

Q:

1. Which of the following statements is incorrect for grain boundary energy? a) The increase in the dislocation density in the structure of the materials has no effect on the grain boundary energy....

Q:

Heat - treatments and Cold Working Laboratory Description: Using common objects, you will experience the phenomena of cold working in metals and alloys. You will also experience the influence of heat...

Q:

Which of the following ASTM grain size numbers would have the largest diameter grains 1 100 1000 10103 Increasing the grain diameter does not influence the material yield strength increases the...

Q:

Material science : please I only need the calculations . Designing a Process for Making Turbine Blades from a Nickel-based Superalloy We are tasked with designing a process for making turbine blades...

Q:

What is the main difference between hot and cold deformation? Why annealing is applied to cold worked metals? Please explain the annealing steps. The hypothetical binary phase diagram is given below....

Q:

Material science : please direct answers Designing a Process for Making Turbine Blades from a Nickel-based Superalloy We are tasked with designing a process for making turbine blades from a...

Q:

Strain Hardening ( aka Cold Work ) and Heat Treat Answer the following using appropriate terminology: Note, to answer all the questions on this pre - lab assignment you will need to do a little...

Q:

Sternhill Limited reported the following selected balances: Other information: 1. There was a stock dividend of $ 50,000 on common shares and a cash dividend of $ 70,000. 2. Of the preferred shares,...

Q:

RAID 6 is used to tolerate up to two simultaneous disk failures. Assume that you have a RAID 6 system based on row-diagonal parity, or RAIDDP; your six-disk RAID-DP system is based on RAID 4, with p...

Q:

The change in the labor classification caused the labor rate variances. This change could also have been responsible for the direct labor time variance. true or false

Q:

What do organization theorists mean by technology ? LO.1

Q:

An unknown sample of Ni 2+ gave a current of 2.36 A in an electrochemical analysis. When 0.500 mL of solution containing 0.028 7 M Ni 2+ was added to 25.0 mL of unknown, the current increased to 3.79...

Q:

A solution was prepared by mixing 5.00 mL of unknown element X with 2.00 mL of solution containing 4.13 g of standard element S per milliliter, and diluting to 10.0 mL. The signal ratio in atomic...

Q:

In Figure 5-6, the x-intercept is 2.89 mM and its standard deviation is 0.098 mM. Find the 90% and 99% confidence intervals for the intercept. Figure 5-6

Q:

Use the following to answer questions 1-4 Determine whether the firm reports each of the following items as part of cash, cash equivalents, or neither in the balance sheet Item Cash, Cash equivalent,...

Q:

ABC Co is considering using a lockbox system. The use of the system will reduce collection time by 2.5 days. The company receives on an average 760 cheques everyday with average value of each cheque...

Q:

XYZ Corporation is a multinational company operating in various sectors, including manufacturing, technology, and services. With a diverse range of operations, the company has a complex financial...