Question: When a close-coiled helical spring is subjected to an axial load, it is said to be under: (a) Shear (b) Bending (c) Torsion (d) Crushing

When a close-coiled helical spring is subjected to an axial load, it is said to be under:

(a) Shear

(b) Bending

(c) Torsion

(d) Crushing

Step by Step Solution

★★★★★

3.52 Rating (155 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Introduction Mechanical Engineering Questions!

Q:

Ambien TM is a sedative used in the treatment of insomnia. It was discovered in 1982 and brought to market in 1992 (it takes a long time for new drugs to undergo the extensive testing required to...

Q:

Create a case brief for the case PETA v. Doughney, including procedural history, the facts, legal questions, rationale, and analysis (if needed).?

Q:

You can use any software to plot and/or to calculate values/data, but if you do, provide (copy/paste) here the code. Data sets relevant for this HW can be found at the UCI Machine Learning...

Q:

1) The acceleration of point A is defined by the relationship a=-5.4sin (kt), where a and t are expressed in ft/s and seconds respectively and k=3 rad/s. If point A starts with an initial velocity...

Q:

A close-coiled helical spring has 60 coils and is made of wire that is 6 mm in diameter. The mean coil diameter is 85 mm. Determine the maximum shear stress in the wire, the elongation of the spring...

Q:

10. A close-coiled helical spring has 60 coils and is made of wire that is 6mm in diameter. The mean coil diameter is 85mm. Determine the maximum shear stress in the wire, the elongation of the...

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

Q . 2 ( a ) What do you mean by factor of safety? ( b ) Write short note on maximum shear stress theory and maximum distortion energy theory, Q . 3 Define equivalent twisting moment and equivalent...

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft is subjected to a bending moment of 4 0 0 Nm and a torque of 2 5 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft with a diameter of 5 0 mm is subjected to a combined loading of a bending moment of 6 0 0 Nm and a torque of 5 0 0 Nm . Determine the principal stresses and the maximum...

Q:

A biologist collected data on a sample of 20 porcupines. She wants to be able to predict the body mass of a porcupine (in grams) based on the length of the porcupine (in cm). Her least squares...

Q:

Moore Wholesalers is preparing its merchandise purchases budget. Budgeted sales are $400,000 for April and $475,000 for May. Cost of goods sold is expected to be 60% of sales. The companys desired...

Q:

Exercise 2 0 - 7 ( Algo ) Change in principle; Change in inventory cost method [ LO 2 0 - 2 ] branches soctoss the Mis South. On Janusy 1 , 2 0 2 4 , management decided to charge foen the averuge...

Q:

Lottery sales. States sell lots of lottery tickets. Table 10.2 shows where the money comes from in the state of Indiana. Make a bar graph that shows the distribution of lottery sales by type of game....

Q:

In a milling operation two side milling cutters are mounted with a desired distance between them so that both sides of a work piece can be milled simultaneously. This set up is called (a) gang...

Q:

Climb milling is chosen while machining because (a) the chip thickness increases gradually (b) it enables the cutter to dig in and start the cut (c) the specific power consumption is reduced (d)...

Q:

The main purpose of boring operation as compared to drilling is to : (a) drill a hole (b) finish drilled hole (b) correct the hole (d) enlarge the existing hole.

Q:

Define static, fixed stack-dynamic, stack-dynamic, fixed heap-dynamic, and heap-dynamic arrays. What are the advantages of each

Q:

how are essential FA used to make other omega - 3 and omega - 6 FAs

Q:

how to calculate the average, min, and max using LAMBDA in computer science