Question: A ball screw for a machine table drive is to be selected. The axial force to be transmitted by the screw is 600 lb. The

A ball screw for a machine table drive is to be selected. The axial force to be transmitted by the screw is 600 lb. The table moves 24 in per cycle, and it is expected to cycle 10 times per hour for a design life of 10 years. Select an appropriate screw.

Step by Step Solution

★★★★★

3.39 Rating (155 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Selecting an appropriate ball screw involves considering various factors such as the axial force spe... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Machine Elements In Mechanical Design Questions!

If the cycle time for the machine in Problem 14 were decreased to obtain 20 cycles/h instead of 10, what would be the expected life in years of the screw originally selected? Data in Problem 14, A...

An 02-series single-row deep-groove ball bearing is to be selected from Table 112 for the application conditions specified in the table. Assume Table 111 is applicable if needed. Specify the smallest...

23 Nickel and Dimed: On (Not) Getting By in America BARBARA EHRENREICH Major changes in welfare legislation in 1996 eliminated cash payments to millions of America's poor, requiring them to find...

You will be asked to select a company that is publicly traded. You must research and secure the SEC 10-K Annual Report for the most recent year. This is often available at the company web site. Look...

Please provide a sketch drawing or CAD drawing of this "Detailed Description of the Reengineered Flight Control Actuator" Please label all parts and make sure to include the Front View, Side View,...

7.6 (A) One axis of the worktable in a CNC positioning system is driven by a ball screw with a 6-mm pitch. The screw is powered by a stepper motor which has 180 step angles using a 2:1 gear reduction...

4. It is required to design a feed drive system for a 3D printer using a DC motor to drive a ball screw through a gearbox with a reduction ratio of 8 to achieve a linear movement along the X-axis of...

One axis of the worktable in a CNC positioning system is driven by a ball screw with a 6 - mm pitch. The screw is powered by a stepper motor which has 1 8 0 step angles using a 2 : 1 gear reduction (...

7.7 One axis of an open-loop positioning system is driven by a stepper motor, which is con- nected to a ball screw with a gear reduction of 3:1 (three turns of the motor for each turn of the screw)....

Discuss the Training and Design process. How are needs assessments (organizational analysis, person analysis, and task analysis) used and how do they indicate a need for training? How are they...

Carryless Arithmetic is basic arithmetic but with the carry from each column ignored. For example, using carryless multiplication, 4 * 4 = 6 but 3* 3 still equates to 9. Below is an example using...

Which of the following is correct regarding treasies? Mutiple Choice A non sell execining tresty requires implementing legaistion to Mave domettic effect. The are not the ise of the land. They may...

Thetermssocialnetworkandsocialmediaareusedfrequentlyinthistext. What doyouthinkeachmeans?Whataretherelationships,similarities,and differences?

The critical speed of a uniform shaft with a rotor at the centre of the span can be reduced by (a) Reducing the shaft length (b) Reducing the rotor mass (c) Increasing the rotor mass (d) Increasing...

Two shafts are shown in the below Fig.38. These two shafts will be torsionally equivalent to each other if their (a) Polar moment of inertias are the same (b) Total angle of twists are the same (c)...

Match List I with List II and select the correct answer using the codes given below the lists: List I A. Node and mode B. Equivalent inertia C. Log decrement D. Resonance List II 1. Geared vibration...

Answer Question 3 (1 point) 3. Lee Martin inherited $20,000 from his great uncle. He would like to invest this money into his retirement account which earns 8% annually. If the money compounds...

Make sure you understand the two alternatives. The "make" means that KCSB assembles and ships all of its regular bicycles. The "buy" means that KCSB pays another firm to assemble and ship some of its...

a. Rocky Mountain Industries, Inc. sells (factors) $1,225,000 of Accounts Receivables with the Sierra Finance Company on a without recourse basis. Sierra Finance acquires the receivables on March 31,...