Question: Compute the stress in a rectangular bar having crosssectional dimensions of 10.0 mm by 30.0 mm when a direct tensile force of 20.0 kN is

Compute the stress in a rectangular bar having crosssectional dimensions of 10.0 mm by 30.0 mm when a direct tensile force of 20.0 kN is applied.

Step by Step Solution

★★★★★

3.38 Rating (160 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Force F 200 kN 20000 N since 1 kN 1000 N Area A Crosssectional area of the rect... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Machine Elements In Mechanical Design Questions!

Q:

The curved bar used on a machine has a rectangular cross section. If the bar is subjected to a couple as shown, determine the maximum tensile and compressive stresses acting at section aa. Sketch the...

Q:

Compute the stress in a round bar having a diameter of 10.0 mm and subjected to a direct tensile force of 3500 N.

Q:

The steel bar has the dimensions shown. Determine the maximum axial force P that can be applied so as not to exceed an allowable tensile stress of Ï allow = 150 MPa. 20 mm 60 mm 30 mm r = 15 mm...

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

Q1 A simply supported beam has a concentrated downward force P at a distance of a from the left support, as shown in the figure below. The flexural rigidity EI is constant. Find the equation of the...

Q:

A section of an engineering assembly includes three plates A , B and C , with dimensions as shown in Figure 7 . All three plates are manufactured from aluminium with a yield strength of 3 0 0 MPa and...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Indicate the mood of the following five sentences. (Indicative, Imperative, Subjunctive) 1 If I were you, I wouldn't drink and drive. 2 She should go to the advisement center before March 1. 3 If he...

Q:

What steps are required in constructing a break-even chart?

Q:

You want to build a workstation that will be used to brute force hash digests. What can you use to ensure sufficient power and speed to crack them?

Q:

Which is not a factor of software quality? (a) Reliability (b) Portability (c) Efficiency (d) Functionality

Q:

A pulley used to transmit power by means of ropes has a diameter of \(3.6 \mathrm{~m}\) and has 15 grooves of \(45^{\circ}\) angle. The angle of contact is \(170^{\circ}\) and coefficient of friction...

Q:

The included angle of a V-grooved pulley is \(30^{\circ}\). The belt is \(20 \mathrm{~mm}\) deep and maximum width is \(20 \mathrm{~mm}\). The mass of belt is \(0.35 \mathrm{~kg}\) per metre length...

Q:

Determine the maximum power that can be transmitted by a belt of \(100 \mathrm{~mm} \times 10 \mathrm{~mm}\) size with an angle of lap of \(160^{\circ}\). The belt density is \(1000 \mathrm{~kg} /...

Q:

During the year, the Senbet Discount Tire Company had gross sales of $555,400. The company's cost of goods sold and selling expenses were $188,300 and $109,700, respectively. The company also had...

Q:

The Express Banquet has two restraunts that are open 24 hrs a day. Fixed costs for the two restraunts together total $459,000 pr year. Service varies from a cup of coffee to a full meal. The average...

Q:

Precision Systems manufactures CD burners and currently sells 18,500 units annually to producers of laptop computers. Jay Wilson, president of the company, anticipates a 15 percent increase in the...