Question: The input shaft for the gear train shown in Figure P861 rotates at 2875 rpm. Compute the rotational speed of the output shaft. Input Shaft

The input shaft for the gear train shown in Figure P8–61 rotates at 2875 rpm. Compute the rotational speed of the output shaft. 

Input Shaft 1 WormA B Shaft 2 Gear E Worm C NA

Input Shaft 1 WormA B Shaft 2 Gear E Worm C NA = 3 NB = 100 D Shaft 3 Nc=2 ND = 80 NE = 20 NF = 85 Output shaft Shaft 4 F

Step by Step Solution

★★★★★

3.31 Rating (148 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

To compute the rotational speed of the output shaft we can use the concept of gear ratios The gear r... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Machine Elements In Mechanical Design Questions!

Q:

Dry methane is supplied by a compressor and precooling system to the cooler of a Linde liquid-methane system (Fig. 9.6) at 180 bar and 300 K. The low-pressure methane leaves the cooler at a...

Q:

The input shaft for the gear train shown in Figure P858 rotates at 3450 rpm cw. Compute the rotational speed and direction of the output shaft. Data in Figure P858 Input shaft A N = 18 NB = 82 Nc =...

Q:

The input shaft for the gear train shown in Figure P860 rotates at 6840 rpm. Compute the rotational speed of the output shaft. Data in Figure P860 Input shaft N = 16 A NB = 48 C 2 Nc = 18 ND = 48 B E...

Q:

The input shaft for the gear train shown in Figure P859 rotates at 12,200 rpm. Compute the rotational speed of the output shaft. Input shaft Gear A B D Gear C N = 12 NB = 50 NC= 12 ND = 40 F NE = 1...

Q:

ca 011/ An epicyclic gear train shown in figure, the arm is keyed to the same shaft as the bad drum and the wheel A is keyed to the second shaft which carries a chain wheel, the chain being operated...

Q:

A new simple gear train shown in Figure below has an input shaft ( 1 ) that requires 1 4 kW to rotate at 1 , 8 0 0 revolutions per minute ( RPM ) . The teeth of the gears are given as follows: A = 2...

Q:

Question 6. A vehicle is being used for a towing event with the gear train shown in Figure 3. The vehicle's engine is designed to operate under the following conditions: 400 Nm of output torque at...

Q:

Question 1 a ) In the gear train shown in Figure 1 , Shafts A and B are co - axial. Gear C has 5 0 teeth and is rigidly mounted on shaft A . Compound gear \ ( \ mathrm { D } - \ mathrm { E } \ )...

Q:

A evra pre ve or we (7 pts) In the two-stage planetary gear train shown in the figure below, internal ring gear 6 is fixed and crank arms C and D are attached to the output shaft. Internal ring gears...

Q:

Consider the reverted compound helical gear train shown with the given numbers of teeth. The normal module of Gear 1 is 3.5 mm and the normal module of Gear 3 is 5 mm. Gear 1 has left-hand helix and...

Q:

For the gear trains sketched in the given figures, compute the output speed and the direction of rotation of the output shaft if the input shaft rotates at 1750 rpm clockwise. Use Figure P839. B...

Q:

A pressure-fed bearing has a journal diameter of 50.00 mm with a unilateral tolerance of 0.05 mm. The bushing bore diameter is 50.084 mm with a unilateral tolerance of 0.10 mm. The length of the...

Q:

How many evaluations of the trapezoid formula are needed to produce a sixth-order integral estimate using extrapolation?

Q:

Investing in employees provides guaranteed return without a risk of losing the investment.

Q:

=+Define component-level data structures. consider inheritance issues.

Q:

What is a coupled locomotive?

Q:

Inertia force acts (a) perpendicular to the accelerating force (b) along the direction of the accelerating force (c) opposite to the direction of the accelerating force (d) in any direction with...

Q:

The reciprocating mass per cylinder in a V-twin engine is 1.5 kg. The stroke is 100 mm for each cylinder. If the engine runs at 1800 rpm, determine the maximum and minimum values of the primary...

Q:

Qno1. a) The cash transactions and cash balances of XYZ, Inc., for December were as follows: 1. The ledger account for Cash showed a balance at December 31 of $114,800. 2. The December bank statement...

Q:

Based on the following.calculate Cost of Goods Sold. (You must show and label your work for credit.) Advertising Expense Cost of Goods Manufactured Finished Goods Inventory, 1/1/2019 Finished Goods...

Q:

2. Which of the following is least likely to be a reason why a long-term construction contract would qualify for revenue recognition over time? A. The customer consumes the benefit of the seller's...