0.5 3.0 0.500- JinryT SCALE 1:2 DATE 5-Jut-22 MATERIAL DIMENSIONAL TOLERANCES ONLESS OTHERWISE SPECTED 0.03 DRAWN...
Fantastic news! We've Found the answer you've been seeking!
Question:
![image text in transcribed](https://s3.amazonaws.com/si.experts.images/answers/2024/05/6645be10b27c3_6726645be108bd45.jpg)
![image text in transcribed](https://s3.amazonaws.com/si.experts.images/answers/2024/05/6645be115982b_6736645be1137d68.jpg)
Transcribed Image Text:
0.5 3.0 0.500- JinryT SCALE 1:2 DATE 5-Jut-22 MATERIAL DIMENSIONAL TOLERANCES ONLESS OTHERWISE SPECTED 0.03 DRAWN x.x 0.015 X.XXX FRACTIONAL 0.005 #1/64 ANGLES 1/2 DATE 01.0 1.5 3.000 0.50- -01.000 3.00 1.500 -01.00 1.50 MATC 700 We u /2022 4:45:09 PM BLOCKS W/ HOLES DWG.No. 125-01A A 2. See the drawing "BLOCKS W/ HOLES" on the next page. Find "D", the distance from hole edge to hole edge. (This is easier to check than center to center on a part that has been produced.) a) What is the "Nominal" distance, D? (i.e. ignore tolerances.) b) When the drawing dimensions are to one decimal place (upper left drawing): i) What are the acceptable upper and lower limits? Check the "Dimensional Tolerances Unless Otherwise Specified" box at the lower left of the drawing. (X.X 0.03) ii) What is the "Tolerance" (i.e. the difference between upper & lower limits)? c) When the drawing dimensions are to two decimal places (upper right drawing): i) What are the acceptable upper and lower limits? Again, check the "Dimensional Tolerances Unless otherwise Specified" box at the lower left of the drawing. (X.XX 0.015) ii) What is the "Tolerance? d) When the drawing dimensions are to three decimal places (lower drawing): i) What are the acceptable upper and lower limits? Again, check the "Dimensional Tolerances Unless otherwise Specified" box at the lower left of the drawing. (X.XXX +0.005) ii) What is the "Tolerance"? 0.5 3.0 0.500- JinryT SCALE 1:2 DATE 5-Jut-22 MATERIAL DIMENSIONAL TOLERANCES ONLESS OTHERWISE SPECTED 0.03 DRAWN x.x 0.015 X.XXX FRACTIONAL 0.005 #1/64 ANGLES 1/2 DATE 01.0 1.5 3.000 0.50- -01.000 3.00 1.500 -01.00 1.50 MATC 700 We u /2022 4:45:09 PM BLOCKS W/ HOLES DWG.No. 125-01A A 2. See the drawing "BLOCKS W/ HOLES" on the next page. Find "D", the distance from hole edge to hole edge. (This is easier to check than center to center on a part that has been produced.) a) What is the "Nominal" distance, D? (i.e. ignore tolerances.) b) When the drawing dimensions are to one decimal place (upper left drawing): i) What are the acceptable upper and lower limits? Check the "Dimensional Tolerances Unless Otherwise Specified" box at the lower left of the drawing. (X.X 0.03) ii) What is the "Tolerance" (i.e. the difference between upper & lower limits)? c) When the drawing dimensions are to two decimal places (upper right drawing): i) What are the acceptable upper and lower limits? Again, check the "Dimensional Tolerances Unless otherwise Specified" box at the lower left of the drawing. (X.XX 0.015) ii) What is the "Tolerance? d) When the drawing dimensions are to three decimal places (lower drawing): i) What are the acceptable upper and lower limits? Again, check the "Dimensional Tolerances Unless otherwise Specified" box at the lower left of the drawing. (X.XXX +0.005) ii) What is the "Tolerance"?
Expert Answer:
Posted Date:
Students also viewed these mechanical engineering questions
-
Taxpayer is retired. TP's sole source of income for 2022 was the sale of an investment property. The sale was a capital asset and she report a capital gain in the amount of $100,000. The sales price...
-
This assignment requires you to complete the 2022 tax reporting for a fictional woman named Anna Smith. Question 1 T1 - step 4 - line 66 This is Anna's taxable income Answer: Question 2 T1 - step...
-
Consider a binomial distribution with 10 trials. Look at Table 2 in the Appendix showing binomial probabilities for various values of p, the probability of success on a single trial. (a) For what...
-
How much taxes do Employees and Employers pay in F.I.C.A? a) Employees and Employers paid 1.45% in taxes. b) Employees and Employers paid 7.65% in taxes. c) Employers and Employees paid 2.7% in...
-
Refer to your answers to Exercise E21-15. In May 2016, RefreshAde produced 20,000 cases of powdered drink mix and sold 23,000 cases, of which 3,000 were produced in April. The sales price was $30,...
-
Temco, Inc., conveyed to the Wynns certain property adjoining an apartment complex being developed by Sonnett Realty Company. Although nothing to this effect was contained in the deed, the sales...
-
In what situations might the use of the relevant cost approach to project planning decisions be preferred over the contribution approach?
-
Yoder Company manufactures luggage sets. Yoder sells its luggage sets to department stores. Yoder expects to sell 1,500 luggage sets for $ 175 each in January, and 1,750 luggage sets for $ 175 each...
-
= Menu W10_Homework.pdf X + Create Sign in - X All tools Edit Convert Sign Find text or tools Q All tools X Export a PDF Exercise 3: Edit a PDF Write a Python function called calculate_discounted_
-
Allen Construction was awarded a contract to build a new office tower on January 1,2019. At the time, Allen's best estimate of total costs to construct the building was $20 million. The total...
-
1. Describe the advantage of the creation of the Chong-Hua Institution for Economic Research. 2. What is the impact of tariffs imposed on Taiwan's imports by Mainland China? 3. Compare the Economic...
-
In a study prepared in 2000, the percentage of households using online banking was projected to be f(t) = 1.6e0.78t (0 t 4) where t is measured in years, with t = 0 corresponding to the beginning of...
-
The Lang Corporation has provided the following account balances: Account Amount Cash $25,000 Short-term Investments 5,000 Accounts Receivable 20,000 Supplies 7,000 Long-term Notes Receivable 3,000...
-
Describe what is meant by manufacturing profit? The account must include, direct materials labour and expenses prime cost indirect costs (factory overheads) work in progress at start and at end ...
-
Briefly discuss the differences between the DCF method, the DDM method, and the market multiples method of valuing a company. What are the strengths AND weaknesses to each method? If you were asked...
-
Write the vector (1, 2, -1) as a linear combination (if possible) as of the vectors (-1, 2, 1), (2, 1, 4)
-
The Ranch 888 Noodle Company sells two types of dried noodles:ramen, at $6.50 per box, and chow fun, at $7.70 per box. So farthis year, the company has sold a total of 110,096 boxes ofnoodles,...
-
What is the purpose of an income statement? The statement of stockholders' equity? The balance sheet? The statement of cash flows?
-
What is a period-of-time statement? Give three examples.
-
What is a point-in-time statement? Give one example.
![Mobile App Logo](https://dsd5zvtm8ll6.cloudfront.net/includes/images/mobile/finalLogo.png)
Study smarter with the SolutionInn App