Question: 1. A 3 phase induction motor is running at 2% slip. If rotor input is 1000 W, then gross mechanical power developed by the rotor

1. A 3 phase induction motor is running at 2% slip. If rotor input is 1000 W, then gross mechanical power developed by the rotor is _____ .
2. A 8 pole 3 phase induction motor operates from a supply whose frequency is 50 Hz. If the slip of the motor is 4%, calculate the speed of the motor
3 . A 3-phase, 6-pole, 50 Hz induction motor develops maximum torque at 960 rpm. If the rotor resistance is 0.12 Ω, what is the standstill rotor reactance?
[Hint with simple calculation]

Step by Step Solution

★★★★★

3.40 Rating (172 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

An induction motor is running at the rated conditions. If the shaft load is now increased, how do the following quantities change? a. Mechanical speed b. Slip c. Rotor induced voltage d. Rotor...

A motor drives a shaft at 12 Hz and delivers 20 kW of power (see figure). (b) If the maximum allowable shear stress is 40 MPa, what is the minimum permissible diameter dmin of the shaft? 12 Hz 20 kW

A motor delivers 275 hp at 1000 rpm to the end of a shaft (see figure). The gears at B and C take out 125 and 150 hp, respectively. Determine the required diameter d of the shaft if the allowable...

Question 1: The flux per pole in a synchronous motor with the field circuit ON and the startor disconnected from the supply is found to be 25 mWb. When startor is connected to the rated supply with...

1.Sketch a line diagram to the types of business organisation on the basis of ownership 2.What do you understand by joint sector companies? Mention the diagrams for the formation of joint sector...

1. Compare the tasks, priorities, and responsibilities of first-line, middle, and top managers. 2. Discuss the difference between efficiency and effectiveness. 3. What is a SWOT analysis. Explain...

What is "profiling"? What are the advantages and disadvantages of its use? How does the use of profiling relate to ethics? 20) A moral and ethical issue raised by the information age is the...

Assignment IV An induction motor has an efficiency of 0 . 9 when the shaft load is 4 5 kW . At this load, stator ohmic loss and rotor ohmic loss each is equal to the iron loss. The mechanical loss is...

please answer all blanks Quality Fender, which uses a standard cost system, manufactured 20,000 boat fenders during 2018. The 2018 revenue a Click the icon to view the revenue and cost information.)...

Julio is a teller at the bank. He will be given the opportunity to work with new customers at the business development desk every Friday. Which job enrichment approach is Julio involved in? Job...

coefficients A variable n(t) is described by a first-order linear differential equation with constant dn(t) T +n(t) = n dt where 7 and no are constants. Let n(0) = no. a) Fort > 0, determine an...

Mortgage Payoff: You take out a 30-year fixed rate mortgage for a house. The amount borrowed is $300,000. The interest rate is 4% per year compounded monthly. You decide to sell the house immediately...

A community hospital system realized that approximately 2,000 patients were leaving its emergency department (ED) each year without receiving medical attention. This hospital system realized that...

Describe what a quality control activity might look like at a t-shirt manufacturing factory. (LO3.3)

An investment is available that pays a tax-free 5%. Ignoring risk, what is the pre-tax return on taxable bonds? The corporate tax rate is 30%. a. 7.14% b. 6.00% c. 8.57% d. 4.20%

Give the products of the following reaction, where T is tritium: dioldehydrase Ad- CH CH3C-COH CoIII) coenzyme B12

Design a 1200-W electric hair dryer such that the air temperature and velocity in the dryer will not exceed 50C and 3 m/s, respectively.

What is the physical mechanism of heat conduction in a solid, a liquid, and a gas?

Liquid ammonia at - 20C is flowing through a 20-m-long section of a 5-mm-diameter copper tube at a rate of 0.09 kg/s. Determine the pressure drop, the head loss, and the pumping power required to...

A large box of mass M is pulled across a horizontal, friction less surface by a horizontal rope with tension T. A small box of mass m sits on top of the large box. The coefficients of static and...

A rifle with a barrel length of 60 cm fires a 10 g bullet with a horizontal speed of 400 m/s. The bullet strikes a block of wood and penetrates to a depth of 12 cm. a. What resistive force (assumed...

An object of mass m is at rest at the top of a smooth slope of height h and length L. The coefficient of kinetic friction between the object and the surface, m k , is small enough that the object...