1 Explain why standard parts are not sectioned in assembly sections 2 marks 2 Describe how cutting plane lines are used 2 marks 3 When should extension lines be broken 1 mark 4 What convention is used for hidden lines on the unsectioned half of a half section view 1 marks 5 State any 3 principles ...

The Answer is in the image, click to view ...

1. Explain why standard parts are not sectioned in assembly sections [2 marks] 2. Describe how...

Fantastic news! We've Found the answer you've been seeking!

Question:

Related Book For answer-question

Manufacturing Processes for Engineering Materials

ISBN: 978-0132272711

5th edition

Authors: Serope Kalpakjian, Steven Schmid

See More Books

Posted Date: Jul 10, 2020 11:32 AM

See More Questions

Explain why the three broken lines (simple tension, I plane strain, and equal biaxial stretching) in Fig. 7.63a I have those particular slopes.
Consider the MPS record below Wk 1 2 3 4 5 6 Forecast 15 25 9 15 22 5 Orders 7 10 10 10 Available ATP MPS On hand = 5, Lot size = 30 a. Complete the MPS record b. Update the record from part a -...
What steps should you follow when planning an Internet research strategy?
Assuming that the Fed judges inflation to be the most significant problem in the economy and that it wishes to employ all of its policy instruments except interest on reserves, what should the Fed do...
a. Generalize the end-to-end delay formula in Section 1.4.3 for heterogeneous processing rates, transmission rates, and propagation delays. b. Repeat (a), but now also suppose that there is an...
Do you agree that EQ (EI) may be more important than IQ and may be applicable to effective interpersonal relations and performance in the workplace? Why?
The solar constant is defined as the average flux of solar energy incident on the outer fringes of the Earth's atmosphere and a commonly used value is \(1.353 \mathrm{~kW} / \mathrm{m}^{2}\). If the...
A wire with mass 40.0 g is stretched so that its ends are tied down at points 80.0 cm apart. The wire vibrates in its fundamental mode with frequency 60.0 Hz and with amplitude at the antinodes of...
How does Lean Management foster a culture of continuous improvement and waste reduction within organizational processes ? Explain
The file P02_18.xlsx contains daily values of the Standard & Poors 500 Index from 1970 to early 2012. It also contains percentage changes in the index from each day to the next. a. Create a histogram...
A chemist has three different acid solutions. The first acid solution contains 20 % acid, the second contains 35 % and the third contains 55 % . They want to use all three solutions to obtain a...
Derive the expression for combined gas law.
Discuss about entropy and avaliable energy?
What strategies or programs could Meda utilize to improve employee well-being?
Discuss about entropy and Clausius inequality.
Define open, closed and isolated systems. Classify each with example.
Assume that Concrete Creations used the FIFO method rather than the weighted average method in its process costing system. Determine the equivalent units of production for the Forming Department for...
The activities listed in lines 2125 serve primarily as examples of A) Underappreciated dangers B) Intolerable risks C) Medical priorities D) Policy failures
An extruder has a barrel diameter of 4 in., a channel depth of 0.25 in., a flight angle of 18, and a pumping zone that is 6 ft long. It is used to pump a plastic with a viscosity of 100 10-4...
It has been stated that the higher the value of m, the more diffuse the neck is, and likewise, the lower the value of m, the more localized the neck is. Explain the reason for this behavior.
A horizontal rigid bar c-c is subjecting specimen a to tension and specimen b to frictionless compression such that the bar remains horizontal. The force F is located at a distance ratio of 2:1. Both...
At December 31, 2025, the fair value of non-trading securities is 41,300 and the cost is 39,800. At January 1, 2025, there was a credit balance of 900 in the Fair Value Adjustment Non-Trading...
On January 1, 2025, Lennon Enterprises acquires 100% of Ono Ltd. for 220,000 in cash. The condensed statements of financial position of the two companies immediately following the acquisition are as...
Which of the following will not be reported in the statement of cash flows? a. The net change in plant assets during the year. b. Cash payments for plant assets during the year. c. Cash receipts from...

1. Explain why standard parts are not sectioned in assembly sections [2 marks] 2. Describe how...

Question:

Expert Answer:

Manufacturing Processes for Engineering Materials

Students also viewed these mechanical engineering questions