Question: 16.Describe PIV rating, Breakdown Voltage, Knee Voltage, Forward Current, Reverse Saturation Current, Maximum Power Rating.?

16.Describe PIV rating, Breakdown Voltage, Knee Voltage, Forward Current, Reverse Saturation Current, Maximum Power Rating.?

Step by Step Solution

★★★★★

3.34 Rating (157 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

PIV rating PIV is the greatest voltage that ought to be applied to the diode in turn around predispo... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

Q:

Power Rating of a Resistor. The power rating of a resistor is the maximum power the resistor can safely dissipate without too great a rise in temperature and hence damage to the resistor. (a) If the...

Q:

Describe how you can increase the maximum operating voltage of a parallel-plate capacitor for a fixed plate separation.

Q:

The alternating current (AC) breakdown voltage of an insulating liquid indicates its dielectric strength. The article "Testing Practices for the AC Breakdown Voltage Testing of Insulation Liquids"...

Q:

3) Low Power CMOS (a) In optimizing power consumption of dimension scaled down CMOS digital circuits, various transistor design and circuit desing techniques were discussed in reference to overcoming...

Q:

An SCR is forced into forward conduction when V F exceeds the q , rating of the device. forward trigger voltage forward breakover voltage forward breakdown voltage forward conducting voltage

Q:

Describe what happens to the electrons when another battery is added to a circuit system. How would you describe the relationship between voltage and current? In other words, in a circuit, how does...

Q:

10. Two flashlights are each powered with four batteries. All of the batteries are 1.5 volts. One of the flashlights has a bulb with a resistance of 6 ohms and the second flashlight has a bulb with a...

Q:

Light Bulb: R1=200 10V R2 =100 Switch R, = ? Figure 1: Use this diagram to fill in Table 1(a). Table 1(a): Using Figure 1, determine the values in this table. R I V P R1 Rz Ra Net 0.2 A 1. Using...

Q:

Nordlink is a proposed subsea high voltage direct current (HVDC) power cable between Norway and Germany. The over 500km long cable will have a capacity of 1400 MW and a operational voltage of 500Kv....

Q:

EIP5012 Question 3 - Array Parameters [30] Using the specifications of a SW250 PV-module and Eland 4mm solar cable determine the array circuit parameters for the following PV-array configurations....

Q:

Write about cost of delivering education below. Cost Of Delivering Education - pros and cons of privatization at the primary secondary and college levels.

Q:

Given O is the center of the circle and

Q:

9 A . f ( x ) = ln ( 3 x - 4 e ^ ( x ^ ( - 2 ) ) ) .

Q:

Using Table 5.2 (Attached), How do Davids motor skills compare to the gross- and fine-motor skill milestones listed in the table? Should Mark and Nicole be concerned if David does not reach the...

Q:

Sigma Design, a computer interface start-up firm with no tangible assets, has invested $50,000 in R&D. The success of the R&D effort as well as the state of the economy will be observed in one year....

Q:

Activities that are outside of the relevant range: A. Only affects fixed costs in a business setting B. Only impact variable costs in a business setting C. Can still affect costs in a business...

Q:

List and describe either the types of teams most commonly used in your organization or of which you are a member. Select one of these teams to analyze. Is this a high-performing team? If yes, why is...

Q:

Excluding the U.S.A., select a specific nation and a company headquartered there. Conduct a quick internet news search regarding this firm, review their website, and discuss any HRM issues as...

Q:

the starch in oatmeal and wheat is composed of what molecules glucose mannose fructose lactose

Q:

In this laboratory activity you will design a cylindrical capacitor. Working with a set of given design specifications, you will employ the use of MATLAB arrays to determine which of six materials...

Q:

For a given de load with a maximum current ILMAX) operating at a given desirable de voltage Vo, use the following checklist to complete a full-wave rectifier design. Note that the maximum voltage...

Q:

Design a full wave (Bridge) rectifier as a dc power supply with a lo load tha 110V (rms) 60Hz household supply through a 8-to-1 step down transformer. TH connected to parallel to the load to provide...

Q:

simulation and calculation part 1.0 The Problem A design company (FOCUS Sdn. Bhd.-CEO: Ahamed Khan) is offering a contract for UCSI EM104 -Electrical Power students to design the following circuits...

Q:

A charger with 5-V, 1-A dc output is to be designed with a ripple voltage of less than 2.5 percent. Assume that a half-wave rectifier circuit (60 Hz) with a capacitor filter is used. The diode has a...

Q:

The input signal voltage to the full-wave rectifier circuit in Figure 2.6 (a) in the text is \(v_{I}=160 \sin [2 \pi(60) t] \mathrm{V}\). Assume \(V_{\gamma}=0.7 \mathrm{~V}\) for each diode....