Question: 2 ) a ) Use the moment - area method to determine the deflection at the free end of the steel ( (

2) a) Use the moment-area method to determine the deflection at the free end of the steel (\(\mathrm{E}=207\mathrm{GPa}\)) cantilever beam shown in the figure.
b) For the same beam, compute the deflection at a point 1.0 m from the fix support A .
2 ) a ) Use the moment - area method to determine

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Question 2 : Deflection in statically determinate beam - Moment Area method ( 2 0 marks ) The beam shown in Figure 2 has a constant elastic modulus ( E ) of 7 0 GPa along its length. The moment of...

Q:

Use the Moment - Area method to calculate the deflection at the free end of cantilever beam shown, Beam is a W 3 1 0 x 2 0 2 ( SI section ) E = 2 0 7 , 0 0 0 MPa Neglect the weight of the beam

Q:

Q3 Beam DE rests on the cantilever beam AC as shown. A square rod of side 10 mm is used for each beam, 1) Determine the deflection at end C if the 25 N. m couple is applied to end E of beam DE. Use...

Q:

A cantilever of length 2 m carries a point load of 20 kN at the free end and another laod of 20 kN at its centre. If E=10 5 N/mm 2 and I=10 6 mm 4 for the cantilever then determine by moment area...

Q:

What specific formulas were used in step 1 for the fixed end moments in this answer? I cant find online anywhere that gives a formula for fixed end moments when the point load is acting on a Node (...

Q:

Determine the position a of the roller support B in terms of L so that the deflection at end C is the same as the maximum deflection of region AB of the overhang beam. EI is constant. Use the Moment...

Q:

Consider the cantilevered beam shown in the figure below that is subjected to the loading shown. The beam has a hollow, rectangular cross - section, as also shown in the figure. For this problem, you...

Q:

( a ) A cantilever 2 metres long is of rectangular section 1 0 0 mm wide and 1 5 0 mm deep. It carries a uniformly distributed load of 2 kN / m over the full length of the beam and a point load of 1...

Q:

Q 1 . Estimate the diameter of bolt required as per five different theories of failure if the bolt is subjected to an pull 1 6 kN and a Shear Force of 1 0 kN . Elastic limit in tension is 3 0 0 N / m...

Q:

Problem 1 Determine the deflection at the left overhang of the beam loaded as shown below using the two methods indicated in the group of your choice. Choose and use only one group. ( No mixing of...

Q:

About designing a smart refrigerator system Required: Determining the task that the refrigerator is doing (reading the barcode of the products and determining the expiry date) Write a scenario for...

Q:

Below are the account balances (all normal) for The Walt Disney Company as of October 3, 2020 after adjusting journal entries but before closing entries. The accounts are listed in alphabetical...

Q:

6. Unequal pay for men and women is a completely indefensible practice and one that must be stopped immediately. Aft er all, can anyone seriously doubt that women have as much right to self-esteem as...

Q:

Sultan Company uses an activity-based costing system. At the beginning of the year, the company made the following estimates of cost and activity for its five activity cost pools: Activity Cost Pool...