Question: ( 3 ) Listed below are the results from liquid and plastic limit tests conducted on a fine - grained soil. From these resultes: (

(3)
Listed below are the results from liquid and plastic limit tests conducted on a fine-grained soil. From these resultes: (20%)
a. Determine the liquid limit for the soil.
LL
b. Determine the plasticity indes for the and PI
c. Classify the soil according to the Unified Soil Classification System.
LIQUID LIMIT TEST RESULT
no answe
?PI=LL-PL
( 3 ) Listed below are the results from liquid

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

The Edelman Gem Company, a small jewelry manufacturer, has been successful and has enjoyed a good growth trend. Now Edelman is planning to go public with an issue of common stock , and it faces the...

Q:

Results from liquid and plastic limit tests conducted on a soil are given below. Liquid limit tests: Number of blows, N Moisture content (%) 13................................................33...

Q:

Results from liquid and plastic limit tests conducted on a soil are given below. Liquid limit tests: Number of blows, N Moisture content (%) 14.........................................38.4...

Q:

Results from liquid and plastic limit tests conducted on a soil are given here. Liquid limit tests: Plastic limit tests: PL = 18.7% a. Draw the flow curve and obtain the liquid limit. b. What is the...

Q:

The results of a sieve analysis on 911.3gr of a soil are shown in the table below: Sieve size (mm) 9.5 4.75 2.36 1.18 0.075 Mass retained (gr) 16 45 247 170 223 Liquid limit test using the Casagrande...

Q:

Please let me know if you need anything, thank you. 2a. Schematically illustrate the subsurface conditions and calculate the effective vertical and total horizontal stresses at Point A before...

Q:

1) The geotechnical engineer decided to use the soil modulus interpreted from the pressuremeter test instead of using a correlation of E = 1 N (MPa) which may be lower and more conservative. Provide...

Q:

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

Q:

Use tre berov Given Information 9% of a soil is retained on No.4 sieve, and 11% passes the No. 200 sieve. It is also known that 10%, 30%, and 60% of the soil is smaller than 0.1 mm, 0.8 mm, and 1.9...

Q:

Some soil has been collected from a site where a commercial centre will be built, to determine its basic geotechnical characteristics in the laboratory. The experimental data from the different tests...

Q:

A dried soil was subjected to particle size analysis with the following results Sieve (mm) Mass Retained (g) 60.000 31.35 6.000 14.4 2.000 12.4 0.600 12.0 0.063 16.5 Pan 7.4 Determine the percentage...

Q:

Compute the least-squares regression equation for the given data set. Use a TI-84 calculator. Round the slope and y-intercept to at least four decimal places. 5.7 4.3 6.4 4.5 6.5 6.0 5.1 1.9 4.9 0.9...

Q:

The figure illustrates the connection of a cylinder head to a pressure vessel using 10 bolts and a confined-gasket seal. The effective sealing diameter is 150 mm. Other dimensions are: A = 100, B =...

Q:

11. (True/False): The Itanium instruction set is completely different from the x86 instruction set.

Q:

Direct Materials Variances The following data relate to the direct materials cost for the production of 2,500 automobile tires: Actual: Standard: 49,100 lbs. at $1.85 per lb. 50,100 lbs. at $1.90 per...