Question: 6 - 4 . Oil flows through the 1 0 0 - mm - diameter pipe with a velocity of 8 m s . If

6-4. Oil flows through the 100-mm-diameter pipe with a velocity of 8ms. If the pressure in the pipe at A and B is assumed to be 60 kPa , determine the x and y components of orce the flow exerts on the elbow. The flow occurs in the iorizontal plane. Take o=900kgm3.
Prob. 6-4
6 - 4 . Oil flows through the 1 0 0 - mm -

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Q 1 . Gasoline flows at the rate of 2 L s through 6 0 mm diameter pipe. Calculate the Reynolds number if density and dynamic viscosity are 7 1 9 k g m 3 and 2 . 9 2 1 0 - 4 P a . s , respectively. [...

Q:

. An oil having an absolute viscosity of 0 . 0 4 8 kg / m - s flows through a 2 5 mm diameter pipe at an average velocity of 0 . 3 m / s . Calculate the pressure drop in 3 0 m of pipe and the...

Q:

Problem 1 (20 points) Fuel oil flows in a horizontal pipe with a diameter of 110 cm. The oil flow rate is 0.45 m/s. The properties of fuel oil are: p = 985 kg/m, and v = 3.810-4 m/s. (a) Calculate...

Q:

(4) A liquid with a constant density (p) is flowing (as shown in figure below) at an unknown velocity (u) through a horizontal pipe of cross-sectional area (A)) at a pressure (P), and then it passes...

Q:

A ABC and A DEF are shown below. To the nearest tenth, how much larger is the area of A DEF than the area of & ABC? A. 8.7 square units B. 17.9 square units C. 24.5 square units D. 35.9 square units...

Q:

1) the reason whey fluid power is used to perform heavy work is b. stiffness A) reliability Origidity 2) the measure of sluggishness in fluid is b. SG a viscosity c. bulk modulus 3) when the fluid...

Q:

1) Oil flows through a 5 cm diameter horizontal smooth pipe at 35C. The maximum velocity with which the oil flows through the pipe is 8m/sec. Calculate the pressure drop for 12 m length of the pipe....

Q:

In an experiment, pressure gauge P in Figure 1 shows a reading of -17.2 kPa. The density of oil and Liquid A are 700 kg/m and 1,600 kg/m respectively. Determine the height of liquid in the piezometer...

Q:

The diagram shows a load-bearing pad resting on a moving belt with lubricating oil supplied at a gauge pressure of 12 kPa at one end of the pad. The oil flows through the space between the two...

Q:

Carbon dioxide at a temperature of 0 o C and a pressure of 6 0 0 kPa ( abs ) flows through a horizontal 4 0 mm diameter pipe with an average velocity of 2 m / s a . Determine the friction factor if...

Q:

If B = (4 x. 20 + 2x 5x, 54 + 4x 13x ) is a basis for P. The coordinate vector of p(x) = 42 + 4x - 11x rolative to the basis B is [pls =

Q:

Use traces to sketch the surface. x = y + 4z Identify the surface. elliptic coneellipsoid elliptic cylinderhyperbolic paraboloidhyperboloid of two sheetselliptic paraboloidhyperboloid of one...

Q:

Adopting the following measures would reduce the expectations gap and lessen public misunderstanding of the auditor s role. a . Publishing a statement of management responsibility b . The auditor...

Q:

When a contingent consideration arising from a businesscombination is classified as equity, how is any change in its fairvalue accounted for if the difference arises due to a change incircumstances 2...