Question: A 1 0 0 - m m long rod has a diameter of d = 1 3 m m . ( Figure 1 ) If

100 - m m

long rod has a diameter of

d = 13 m m . (

Figure

1)

If an axial tensile load of

10

kN is applied to it

,

determine the change in its diameter.

E = 75

GPa,

v = 0.35

Express your answer to three significant figures and include the appropriate units. Enter negative value if diameter decreases and positive value if diameter increases.

Provide Feedback

A 1 0 0 - m m long rod has a diameter of d = 1 3

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

#1 Calculate the stress developed in the following members that are each subjected an axial tensile load of 100kips. SHOW ALL REFERENCES AND PAGES: a: 8" sch.40 (8" STD) pipe b: HSS 2x2x1/4 c: 6x8...

The 100 mm long rod has a diameter of 15 mm. If an axiaI tensile load of 10 kN is applied to it, determine (a) the normal stress in the rod (b) the axial strain in the rod (c) the lateral strain in...

A thin rectangular polymer plate PQRS of width b = 418 mm and height a = 188 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 3.2 mm and corner R is...

GI Info QUESTION 3 (a) [20 marks] A cylindrical brass bar of 56.25 mm diameter and of length 900 mm is subjected to an axial tensile load of 170.1 kN. The extension of the bar is measured as 0.853...

1. The dimension of strain is? a) LT-2 b) N/m2 c) N d) Dimensionless 2. What is tensile strain? a) The ratio of change in length to the original length b) The ratio of original length to the change...

Problem 5 (Deformation) For shock loading in a ductile material, Table 3-2 recommends the following design stress. The percent elongation of 12%% is in the ductile range. 04 - s./12 = 196 kei/12 = 16...

The tie rods in the press in Figure 3-3 are made of the steel alloy AISI 5160 OQT 900. Each rod has a diameter of 2.00 in and an initial length of 68.5 in. An axial tensile load of 40 000 lb is...

Question 1 (a) A cylindrical 1045 steel rod is subjected to repeated compression-tension stress cycling along its axis. The S-N curve of 1045 steel is shown in Figure Q1. Apply the data given in...

Matlab Questions: (Please write all the code and comments necessary; must include function)...

PROBLEMS For the following problems, unless noted otherwise, refer to Appendices F and/or G for necessary mechanical prop- erties. Section 4-1 Poisson's Ratio A 1. A 2 in. diameter AISI 1020 steel...

Ashley had $10,000 in credit card debt. She negotiated a settlement with the credit card company. Ashley paid $5,000 of the credit card debt, and the credit card company agreed to cancel $5,000 of...

Analyze each situation and indicate the correct dollar amount for the adjusting entry. 1. Ending inventory of supplies is $95. 2. Amount of supplies used is $280. (Balance Sheet) (Income Statement)...

Interfund reimbursements represent repayments to the funds that initially recorded or by the fund actually responsible for the payment. (Enter only one word per blank.)

5.8. Louis Hooper, manager of the Tahoe City street maintenance department must decide about increasing the snow removal equipment. He has identified three mutually exclusive states of weather: no...