Question: A 1 0 c m long 3 0 4 Stainless Steel rod is subjected to a tensile load of 4 k N . The cross

A 10cm long 304 Stainless Steel rod is subjected to a tensile load of 4kN. The cross sectional of the rectangular rod is given in the Figure 1. The modulus of elasticity for 304 Stainless Steel is given as 193GPa. Calculate the following:
(a) Cross-sectional area
(b) Engineering stress
(c) Engineering strain
Figure 1.
A 1 0 c m long 3 0 4 Stainless Steel rod is

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

For each item listed in the table below, input the balance for the date range 10/1/20XX to 12/1/20XX. For the Journal, input the balance for the date range 11/13/20XX to 12/1/20XX. Note: Enter your...

Q:

Question 1 (a) A cylindrical 1045 steel rod is subjected to repeated compression-tension stress cycling along its axis. The S-N curve of 1045 steel is shown in Figure Q1. Apply the data given in...

Q:

For each of the following cases, determine an appropriate characteristic length L c and the corresponding Biot number Bi that is associated with the transient thermal response of the solid object....

Q:

( 3 pts ) Strain. A short compression member 3 in , by 3 in . in cross - section and 1 4 in . long is subjected to a 6 0 , 0 0 0 l b axial compressive load. As a result, the length of the member is...

Q:

Summarize this for me. Someone who understand the HEA and MEA perfectly and also the summary should be 2 or over 2 pages. Someone who understands this perfectly A scrap-tolerant alloying concept...

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

Each arm comprises a horizontal beam made from an AISI651 stainless steel tube (see Table 1 for the material properties) of length L = 35 mm, inner diameter d = 375 m and outer diameter do = 575 m,...

Q:

Chapter 7 Locate the x - x and Y - Y centroidal axes for the areas shown. Problem 1 Problem 2 Chapter 8 Calculate the moments of inertia with respect to both centroidal axes for the areas shown....

Q:

Question 1 You are employed as a metallurgist by a motor car manufacturer that uses a very low carbon ferritic sheet steel for its body panels. The general manager calls you in and tells you that...

Q:

1. The dimension of strain is? a) LT-2 b) N/m2 c) N d) Dimensionless 2. What is tensile strain? a) The ratio of change in length to the original length b) The ratio of original length to the change...

Q:

In the HMO study the "Intentions to enroll" by "Intentions to have more children" cross- tabulation is shown in Table 16-3. Interpret it in the context of Figure 16-4.

Q:

The standard therapy used to treat a disorder cures 60% of all patients in an average of 140 visits. A health care provider considers supporting a new therapy regime for the disorder if it is...

Q:

A major impetus fueling financial mergers during the 1 9 8 0 s was _ _ _ _ _ _ _ _ .

Q:

The following information relates to Smith Jewelers, Inc. Net Sales Revenue Cost of Goods Sold Interest Expense Operating Expenses Calculate the operating income. OA. $226,700 OB. $188,000 OC....