Question: A 4 - m - diameter vertical cylindrical milk tank rotates at a constant rate of 1 5 rpm . If the pressure at the

A 4-m-diameter vertical cylindrical milk tank rotates at a constant rate of 15rpm. If the pressure at the center of the bottom surface is 130 kPa, determine the pressure at the edge of the bottom surface of the tank. Take the density of the milk to be 1030 kg/m3.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

A 3-m-diameter vertical cylindrical milk tank rotates at a constant rate of 12 rpm. If the pressure at the center of the bottom surface is 130 kPa, determine the pressure at the edge of the bottom...

Q:

1. Water at 93.3C is being pumped from a large storage tank at 1atm abs at a rate of 0.189m3/min by a pump. The motor that drives the pump supplies energy to the pump at a rate of 1.49kW. The water...

Q:

A vertical cylindrical water tank of diameter D=1 m is being drained via a hole of diameter d = 5 cm at the bottom of the tank. The speed of the water through the hole is 2gh, where h(t) is the depth...

Q:

X = 9, Y = 1 Question: A new salt factory is being developed at a remote location in salt affected region of Victoria. This factory does not have access to utilities such as grid electricity, piped...

Q:

Ground coal is slurried with water in a pit, and the slurry is pumped out of the pit at a rate of $500 \mathrm{gpm}$ with a centrifugal pump and into a classifier. The classifier inlet is $50...

Q:

12a please circle the answers 1. [-I1 Points] WAUNIPHYSAV1 12.P.002. ASK YOUR TEACHER PRACTICE ANOTHER A 4.5-kg, three legged stool supports a 95-kg person. If each leg of the stool has a...

Q:

AP Calculus AB/EC Related Rates Draw a gure for each problem. Label all variables. Identify an equation that relates the rates given. Differentiate with respect to time. Answer the question in a...

Q:

Hello, you already did chapter 1 and 2 of my MASTERS Thesis already for me. (See attached) So normally you know masters thesis consist of 5 chapters right ??..... But in this case my thesis will be 4...

Q:

Solve the following problems neatly and systematically. Use free-floating decimals in all your calculations and express your answers in 4 decimal places. Please answer 1,2,3 1. Derive a formula to...

Q:

Reconsider Prob. 3126. Using EES (or other) software, investigate the effect of rotational speed on the pressure difference between the center and the edge of the bottom surface of the cylinder. Let...

Q:

A horizontal pipe 30 cm in diameterand 420 m long has a wall thickness of l cm. The pipe is commercial steel and carries water from a reservoir to a level 1 00 m below and discharges into the air. A...

Q:

Use Simulink to solve Problem 64. Plot h(t) for both parts (a) and (b). In Problem 64 V = 1/3 (R/H)2 h3 Suppose that the cup's dimensions are R = 1.5 in. and H = 4 in. a. If the flow rate from the...

Q:

12201. The motor at C pulls in the cable with an acceleration aC = (3t2) m>s2, where t is in seconds. The motor at D draws in its cable at aD = 5 m>s2. If both motors start at the same instant from...

Q:

1 Tip Top Corp. produces a product that requires seven standardgallons per unit. The standard price is $10 per gallon. If 4,000units required 29,100 gallons, which were purchased at $9.8 pergallon, 2...