A bar of length 1000mm and diameter 30mm is centrally bored for 400mm, the bore diameter 10mm

Fantastic news! We've Found the answer you've been seeking!

Question:

A bar of length 1000mm and diameter 30mm is centrally bored for 400mm, the bore diameter 10mm as shown in figure-3. Under the load of 25 KN, if the extension of the bar is 0.185mm, what is the modulus of elasticity of the bar?

Related Book For answer-question

Applied Linear Algebra

ISBN: 978-0131473829

1st edition

Authors: Peter J. Olver, Cheri Shakiban

See More Books

Posted Date: Aug 30, 2021 03:27 AM

See More Questions

If the pattern shown in Figure 3 is continued indefinitely what fraction of the original square will eventually be painted? Figure 3
As shown in Figure P18.42, water is pumped into a tall vertical cylinder at a volume flow rate R. The radius of the cylinder is r, and at the open top of the cylinder a tuning fork is vibrating with...
A reboiled stripper as shown in Figure is to be designed for the task shown. Determine(a) The number of variables.(b) The number of equations relating the variables.(c) The number of degrees of...
Passenger table (passengerid, address etc.) Flight table (flight id, departure, destination, depDate) Booking table (cID, fid, date, cost) a. Find Passengers who live in Chicago b. Total number of...
In teams of three or four, investigate whether your local community has a housing or landlordtenant court. What are some of the disputes decided by this court?
Two-phase interfacial boundary conditions, in S2.1, boundary conditions for solving viscous flow problems were given. At that point no mention was made of the role of interfacial tension. At the...
(a) Use Figure $7.2 a$ to calculate the $x$ components of the momenta of the two carts at $t=30,60$, and $90 \mathrm{~ms}$. (b) What is the $x$ component of the momentum of the system at...
Presented below is information related to Zonker Company. 1. On July 6, Zonker Company acquired the plant assets of Doonesbury Company, which had discontinued operations. The appraised value of the...
Total Energy (a) Conserved 12. Which one of the following is true in the case of inelastic collisions? Kinetic Energy Conserved Momentum Conserved (b) Conserved Not Conserved Conserved (c) Conserved...
Imagine that an arrow is shot from the bottom of a well. It passes ground level at 1.1 s and lands on the ground at 4.7 s. a. Define variables and write a quadratic function that describes the height...
Step 1: Choose any two publicly held companies and get their Annual Reports for the most recent year. Step 2: Locate the four financial statements of each company (Statement of Financial Position,...
How much would a $6,750 investment yield after 65 years at an annual rate of return of 6%?
OANDA Project Here is the platform that we will be using. www.oanda.com Online Forex Trading & Forex Broker | OANDA We need to familiarize ourselves with the OANDA FX trading platform. We need to set...
Describe the historical simulation method and explain why it is used to calculate bond Value-at-Risk with reference to how market risk affects bond prices.
A swiss stock has a monthly risk of 0.02 and the CFH/$ exchange rate has a monthly risk of 0.07. The correlation of these two risks is 0.21. What is the annual risk of a US investment into this stock?
A ball rolls off of a horizontal table with some speed over level ground below. After 0.35s of falling, the ball hits the ground at a distance of 1.38m from the bottom edge of the table. What was the...
Write a c++ program that uses while loop(s) to perform the following steps: Prompt the user to input two integers: firstnumm and secondnum. Firstnum must be less than secondnum. (assume at least one...
For the following arrangements, discuss whether they are 'in substance' lease transactions, and thus fall under the ambit of IAS 17.
Let A be a general n n matrix. Determine the exact number of arithmetic operations needed to compute A-1 using (a) Gaussian Elimination to factor P A = LU and then Forward and Back Substitution to...
In the bar with fixed ends discussed in Example 11.2. which point experiences the greatest displacement? Which point experiences the greatest stress? The greatest strain?
True or false: If A is symmetric, then A2 is symmetric.
Hannah Gilpin is the controller of Blakemore Auto Glass, a division of Eastern Glass and Window. Her division has been under pressure to improve its divisional operating income. Currently, divisions...
Describe the five-step decision-making process.
Key success factors. Dalworth Construction Company provides construction services for major projects. Managers at the company believe that construction is a people-management business, and they list...

A bar of length 1000mm and diameter 30mm is centrally bored for 400mm, the bore diameter 10mm

Question:

Expert Answer:

Applied Linear Algebra

Students also viewed these accounting questions