A beam simply supported over a span of 5 m, is loaded with a central point...
Fantastic news! We've Found the answer you've been seeking!
Question:
Transcribed Image Text:
A beam simply supported over a span of 5 m, is loaded with a central point load of 80 kN. The section of the beam is a rectangle, 200 mm wide and 400 mm deep. At a cross- section distant 2 m from the support, at a point 75 mm from the N.A. Find the principal stresses (a) 9.844 N/mm (Ten), 4.219 N/mm (comp) (b) 9.844 N/mm (Comp), 4.219N/mm (Ten) (c) 9.844N/mm(comp), 4.219N/mm(comp) (d) 9.844 N/mm (Ten), 4.219 N/mm (Ten) A beam simply supported over a span of 5 m, is loaded with a central point load of 80 kN. The section of the beam is a rectangle, 200 mm wide and 400 mm deep. At a cross- section distant 2 m from the support, at a point 75 mm from the N.A. Find the principal stresses (a) 9.844 N/mm (Ten), 4.219 N/mm (comp) (b) 9.844 N/mm (Comp), 4.219N/mm (Ten) (c) 9.844N/mm(comp), 4.219N/mm(comp) (d) 9.844 N/mm (Ten), 4.219 N/mm (Ten)
Expert Answer:
Related Book For
Posted Date:
Students also viewed these mechanical engineering questions
-
A beam simply supported at the ends has the crossection and is located with a concentrated load p as shown if the maximum flexural stress is not to exceed 20ksi determine the safe value of p
-
A simply supported composite beam with a 3.6 m span supports a triangularly distributed load of peak intensity q0 at mid span (see figure part a). The beam is constructed of two wood joists, each 50...
-
A beam simply supported at both ends is subjected to a constant load Po at its centre (x = L/2). The beam's flexural rigidity is El and is made of a material with mass per unit length p. Determine...
-
Complete the attached SWOT Worksheet using information from the Cotopaxi case. Use your SWOT Worksheet to help you answer the question: What should Davis Smith/Cotopaxi do (for company...
-
The unadjusted trial balance and income statement amounts from the December 31 adjusted trial balance of Wallace Production Company follow. Requirement 1. Journalize the adjusting and closing entries...
-
At January 1, 2022, Youngstown Company reported the following property, plant, and equipment accounts: The company uses straight-line depreciation for buildings and equipment, its year-end is...
-
Extend the analysis of the laminar-flow reactor for a power-law fluid. Perform some computations using the PDEPE solver, and show how the power-law index affects the conversion in the reactor.
-
Economist Lester Thurow once posed the following question: If you were the president of your own country and could choose one of two industries in which to specialize, computer chips or potato chips,...
-
Output: Write a program that asks the user for the number of columns in a square matrix (2-d array with the same number of rows and columns). Randomly fill the matrix with int values between 1 and...
-
The file P02_07.xlsx includes data on 204 employees at the (fictional) company Beta Technologies. For this problem, consider this data set as the population frame. a. Using the method in this section...
-
Assume Nortel Networks contracted to provide a customer with Internet infrastructure for $2,450,000. The project began in 2021 and was completed in 2022. Data relating to the contract are summarized...
-
What is test checking? In what circumstances test checking is advisable? What factors are to be considered before resorting to test checking? What are the advantages and disadvantages of test...
-
Discuss various classes of error and state in each case the effect they might have on the trial balance being discovered.
-
Write short notes on: a. Batch total b. Test data c. Check digit
-
Discuss the advantages and disadvantages of balance sheet audit. Also state the auditors position in relation to balance sheet audit.
-
Distinguish between internal control system and internal check system.
-
ABC Inc. pays its general manager an annual bonus of 6% of profit after deduction for both bonus and corporate income tax. For the year 2020, the company realized profit of 10 800,000 before said...
-
The percentage of completion and completed contract methods are described in the FASB ASC. Search the codification to find the paragraphs covering these topics, cite them, and copy the results.
-
The truss consists of three members, each made from A-36 steel and having a cross-sectional area of 0.75 in 2 . Determine the greatest load P that can be applied so that the roller support at B is...
-
The ball is truncated at its ends and is used to support the bearing load P. If the modulus of elasticity for the material is E, determine the decrease in the balls height when the load is applied. P...
-
If the wide-flange beam is subjected to a shear of V = 20 kN, determine the maximum shear stress in the beam. 200 mm 20 mm 20 mm - 300 mm 200 mm 20 mm
-
Which of the following is true about cash balance plans? I. Past service credit is available. II. Employer guarantees a minimum rate of return. III. Participants direct investments in hypothetical...
-
Which of the following is true regarding a SIMPLE IRA plan? A. The employer must have 100 or more employees. B. Participant loans are allowed. C. It can be combined with a money purchase plan. D. An...
-
An SEP has which characteristic? A. Loans and hardship withdrawals are available. B. Age-weighting or cross-testing is permitted. C. Social Security integration is permitted. D. Employer matching is...
Study smarter with the SolutionInn App