Question: A beam with a rectangular cross section of width 3 2 mm and height 7 8 mm is subjected to a shear force of 2

A beam with a rectangular cross section of width 32 mm and height 78 mm is subjected to a shear force of 28.7 kN. Determine the maximum shear stress in the cross section in MPa (absolute value).

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

A thin steel beam AB used in conjunction with an electromagnet in a high-energy physics experiment is securely bolted to rigid supports (see figure). A magnetic field produced by coils C results in a...

Q:

2. (35 pts) The beam ABCDE has simple supports at A, C, and E and a hinge/pin at B. It has a rectangular cross section of width b = 8 cm and height h = 24 cm. A concentrated load of 160 kN acts at D,...

Q:

A solid cylindrical shaft with a diameter of 7 0 mm is subjected to a bending moment of 8 0 0 Nm and a torque of 6 0 0 Nm . Calculate the principal stresses, maximum shear stress, and the equivalent...

Q:

computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 \ deg C to 3 0 \ deg C . Assume...

Q:

Computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 C to 3 0 C . Assume the specific...

Q:

Computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 C to 3 0 C . Assume the specific...

Q:

Question 1: A cantilever beam is subjected to uniformly distributed dead load of 17 kN/m (and concentrated live load of 25 kN). Of the total live load, 30% is considered sustained for 1 year. The...

Q:

A prismatic bar with rectangular cross section (20 mm x 40 mm) and length 2.8 m is subjected to an axial force P-70 kN that produces an elongation 6-1.2 mm. Two stress elements, A and B are...

Q:

The beams shown in the figure are subjected to bending moments M = 250N m. Each beam has a rectangular cross section with height h = 44mm and width b = 10mm (perpendicular to the plane of the...

Q:

2. (a) What is released structure (primary structure)? (b) A concentrated force P=200 kN moves horizontally across the beam. The horizontal reactions at the supports may be neglected. The beam has a...

Q:

Calculate the voltages Vo and Vab, the currents io and ix, the power of Psi in the Figure.3 via Ohm's Law, KVL, and KCL. The voltage sources of the circeuit are Vs1 = 250 Vol, Vs2 = 50 Volt. 70 170...

Q:

Several brands of antacids use Al(OH)3 to react with stomach acid, which contains primarily HCl: Al(OH)3(s) + HCl(aq)AlCl3(aq) + H2O(l) (a) Balance this equation. (b) Calculate the number of grams of...

Q:

Question 1 6 . XYZ Corp is considering acquiring a Korex machine with a $ 5 0 , 0 0 0 initial investment. Based on its future cash flows Korex has an Intemal Rate of Return ( IRR ) of 1 2 % . A Zorez...

Q:

EVALUATION OF P/E RATIO Step 1: Read the articles. These articles contain examples of evaluating P/E ratio. You will be using these examples to answer the questions listed at the bottom of the topic...