Question: A block is moving along a horizontal surface at 12.5 m/s. It then slows down to 9.25 m/s and travels a distance of 8.75 m.

A block is moving along a horizontal surface at 12.5 m/s.  It then slows down to 9.25 m/s and travels a distance of 8.75 m. 

If the block has a mass of 1.35 kg, what is the power supplied to the block, by friction?

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

1 Calculate the acceleration a 925 ms2 125 ms22875 m a 855625 m2s2 15625 ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Physics Questions!

Q:

I need help on part 2 pf PLE Chapter 11 Part 2: The CFO of Performance Lawn Equipment, J. Kenneth Valentine, would like to have a model to predict the net income for the next 3 years. To do this, you...

Q:

The following additional information is available for the Dr. Ivan and Irene Incisor family from Chapters 1-5. Ivan's grandfather died and left a portfolio of municipal bonds. In 2012, they pay Ivan...

Q:

1. if a block is moving to the left at a constantvelocity, what can one conclude? a) there is exactly one force applied to the block b) the net force applied tot the block is directed to theleft c)...

Q:

Let A, B be sets. Define: (a) the Cartesian product (A B) (b) the set of relations R between A and B (c) the identity relation A on the set A [3 marks] Suppose S, T are relations between A and B, and...

Q:

A block is moving along a horizontal surface at 12.5 m/s. It then slows down to 9.25 m/s and travels a distance of 8.75 m. If the block has a mass of 1.35 kg, what is the power supplied to the block,...

Q:

help me answer these questions: Question 7 Block X Block Y Vx i Figure 1. Before the collision Block X Block Y Vxy =X Figure 2. After the collision Block X slides along a horizontal surface with a...

Q:

Question #4 A force of 516 N is required to just get a mass of 75 kg moving along a horizontal surface. While a force of 630 N cause the mass to accelerate at 6 m/s-. a. Calculate the coefficient of...

Q:

LS DETAI MY NOTES A small block of mass m ls place on top of a hill as shown in the gure at the right, a height h above a horizontal track. The hill is frictionless, but when the block reaches . the...

Q:

6. [-/1 Points] DETAILS OSUNIPHYS1 7.2.P.048. MY A 6.0 kg body has eight times the kinetic energy of a 7.5 kg body. Calculate the ratio of the speeds of these bodies. V6.0 kg _ V7.5 kg + Additional...

Q:

Pls answer all the questions according and to the best of your capabilities Uniform Circular Motion Activity Sheet A6 Purpose: The purpose of this activity is to explore the characteristics of the...

Q:

Class Management | Help Week7 Begin Date: 7/16/2023 12:01:00 AM -- Due Date: 7/25/2023 11:59:00 PM End Date: 8/10/2023 11:59:00 PM (4%) Problem 18: A block of mass my = 18 kg slides along a...

Q:

A team of researchers was asked to study the extent of broadband access in Canada. It found some very old data online on broadband access from the start of 2001 to the end of 2003 and used it to...

Q:

If the H for C2H4 + H2 ( C2H6 Is 65.6 kJ, what is the H for this reaction? 2C2H4 + 2H2 ( 2C2H6

Q:

6. What is the role of a staff position in a line-and-staff organization?(minimum 40 words) I. What is the role of a staff position in a line-and-staff organization? (minimum 40 words)

Q:

This information is available for Abdullah's Photo corporation for 2015, 2016 and 2017. 2015 2016 2017 Beginning inventory $ 100,000 $ 300,000 $ 400,000 Ending inventory $ 300,000 $ 400,000 $ 480,000...

Q:

Two continuous ideal PFRS with volume V1 and V2, respectively, and V1 is greater than V2, are connected in series. In the reactors, a second order irreversible reaction takes place. Which of the...

Q:

Given the unity feedback system shown in Fig. 1, where K G(s) (s +1)(s +2)(s + 3)

Q:

Torque vs. angle of twist data for a solid round shaft of 2024-T351 Aluminum alloy are shown below The radius of the shaft is r= 10 mm and the length L= 200 mm. 400 350 300 250 200 150 100 50 2 6. 8...

Q:

Water at 24C enters a square duct with a 3cm x 3cm cross section. The flow rate of the water is 0.015 kg/s. The walls of the duct are maintained at a uniform temperature of 150C. Assume fully...

Q:

What types of technology are being used to enhance transportation equipment safety? Tracking and tracing loads, tracking carrier performance, lower administrative costs Enhanced safety features,...

Q:

For a wavelength of 420 nm, a diffraction grating produces a bright fringe at an angle of 26. For an unknown wavelength, the same grating produces a bright fringe at an angle of 41. In both cases the...

Q:

The 0 meson is a particle that has a rest energy of 135.0 MeV (see Table 32.3). It lives for a very short time and then decays into two g-ray photons: 0 + . Suppose that one of the g-ray photons...

Q:

One kilogram of glass ( = 2.60 103 kg/m3) is shaped into a hollow spherical shell that just barely floats in water. What are the inner and outer radii of the shell? Do not assume that the shell is...

Q:

A company sells three models of radar detector units. It buys three basic units (E, F, and G) from a Japanese manufacturer and adds one, two, or four lights (component D) to further differentiate the...

Q:

Questions 1. Which type of production processjob shop, batch, repetitive, or continuousis the primary mode of operation at Stickley Furniture? 2. Suppose that the company has just received an order...

Q:

As s lime that you are tire manager of a shop that assembles power too Is. You have just received an order for 50 chain saws, which are to be shipped at the start of week 8. Pertinent information on...