Question: A call for a bid or estimate for materials to be furnished or work to be done is not considered a(n): Best answer choice? offer.

A call for a bid or estimate for materials to be furnished or work to be done is not considered a(n):

Best answer choice?

offer.

request for proposal.

invitation to acceptance.

acceptance.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Law Questions!

Q:

The Hoylake Rescue Squad receives an emergency call every 1, 2, 3, 4, 5, or 6 hours, according to the following probability distribution. The squad is on duty 24 hours per day, 7 days per week: Time...

Q:

Match each of the numbered definitions with the correct term in the following list. Write the letter of your choice in the answer column. a. Acceptance b. Counteroffer c. Invitation to trade d. Lapse...

Q:

A call for a bid or estimate for materials to be furnished or work to be done is not considered an offer, but rather: Question 10 options: All of the options are correct. something that can be...

Q:

A call for a bid or estimate for materials to be furnished or work to be done is not considered an offer, but rather: Question 10 options: All of the options are correct. something that can be...

Q:

A call for a bid or estimate for materials to be furnished or work to be done is not considered an offer, but rather: a request for an offer. an invitation to negotiate. something that can be...

Q:

Question 1(10 points) Directions:Match each of the numbered definitions with the correct term in the following list. Question 1 options: 1 2 3 4 5 6 7 8 9 10 A new and different response to an offer....

Q:

A request for proposal is: Multiple Choice a newspaper or tv advertisement a reward for information that might lead to the arrest of a criminal a call for a bid or estimate for materials to be...

Q:

A request for proposal is: Multiple Choice the equivalent to a bill of lading a call for a bid or estimate for materials to be furnished or work to be done a newspaper or tv advertisement a reward...

Q:

MGT254. Contracts and Procurement MGT 254. Contracts and Procurement Assignment 1 Writing a Statement of Work (SOW) Introduction The full life-cycle of a procurement of a good or service is typically...

Q:

Chapter 9 from Business Law and the Legal Environment was adapted by The Saylor Foundation under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 license without attribution as requested...

Q:

FACT SHEET FOR YOUR CONFERENCE ASSOCIATION NAME: Statistics Notes Name of Conference: List the name you are going to give your conference, this will be used in all of your marketing (HTM 2025 Annual...

Q:

13) Solve the following equation. x +5x+6=20 14) Draw a rough graph of f(x)=-x + 4x-3. You should plot the vertex and at least two other points. 15) Solve the equation: 3-4x +7=0

Q:

The linkage mechanism shown below has two rotating arms linked by a pin (A) sliding in a slot on link OD. At the instant shown, pin A has an upwards velocity of 1.5 m/s; the component of pin A's...

Q:

Find the following for the function f ( x ) = 5 x 3 7 x - 6 . ( a ) f ( 0 ) ( b ) f ( 1 ) ( c ) f ( - 1 ) ( d ) f ( - x ) ( e ) - f ( x ) ( f ) f ( x 1 ) ( g ) f ( 4 x ) ( h ) f ( x h )

Q:

A fan that can provide air speeds up to 50 m/s is to be used in a low-speed wind tunnel with atmospheric air at 25C. If one wishes to use the wind tunnel to study flat-plate boundary layer behavior...

Q:

Determine the force in each member of the Fink truss shown. State whether each member is in tension or compression. 42 IN D. 28AN 25IN 15m 1.5

Q:

An I/O-bound program is one that, if run alone, would spend more time waiting for I/O than using the processor. A processor-bound program is the opposite. Suppose a short-term scheduling algorithm...

Q:

Use the ideal gas equation of state to estimate the molar volume in m3tmol and the density of air in kg/m 3 at 40C and a gauge pressure of 3.0atm.

Q:

On an icy day, you worry about parking your car in you driveway, which has an incline of 12o. Your neighbors driveway has an incline of 9.0o, and the driveway across the street is at 6.0o. The...

Q:

Insimbi Chemicals Corporation John Martins, the production manager of Insimbi Chemicals, in South Coast, Durban is preparing his quarterly report, which is to include a productivity analysis for his...

Q:

3. An initial value (anchoring).

Q:

4. Similarity (representativeness).

Q:

2. In this chapter, the reader should reflect on the following concepts: Idealized system design, analogue thinking, contrast principle, consistency principle, reciprocity principle, scarcity...